Arctic Cat DVX 90/90 UTILITY Скачать руководство пользователя

Страница: 52 / 86

4. Install the oil pump drive chain and driven gear and

secure the gear to the pump shaft with the nut tight-

ened to 7 ft-lb; then install the oil pump baffle and

secure with the cap screws. Tighten securely.

YT152A

5. Install the inner magneto housing using a new gasket

making sure the alignment pins are correctly located;

then secure with the five internal and three external

cap screws.

YT152B

YT031A

6. Install the stator/trigger coil assembly and secure

with four cap screws. Tighten securely.

YT155A

7. Install the rotor flywheel making sure the crankshaft

and flywheel bore are clean and free of any oil; then

with the key in place, secure with the flywheel nut

coated with red Loctite #271. Tighten to 30 ft-lb.

YT143

8. Install the cooling fan and secure with four cap

screws; then install the fan shroud.

Installing Engine/

Transmission

1. From the left side, place the engine/transmission into

the frame tilting the top-side forward to clear the

frame member.

YT014

2. Install the two front engine mounting brackets on the

frame and tighten the cap screws securely; then

install the two front through-bolts. Do not tighten at

this time.

Содержание DVX 90/90 UTILITY























































































Результаты поиска

Содержание DVX 90/90 UTILITY

Отзывы:

Похожие инструкции для DVX 90/90 UTILITY

Бренды по названию

Популярные бренды

Arctic Cat DVX 90/90 UTILITY, Руководство по обслуживанию

Результаты поиска

Содержание DVX 90/90 UTILITY

Отзывы:

Похожие инструкции для DVX 90/90 UTILITY

Бренды по названию

Популярные бренды