Arctic Cat DVX 90/90 UTILITY Скачать руководство пользователя | Manualshive

Страница: 35 / 86

background image

32

3. Place the cylinder head on the surface plate covered

with #400 grit wet-or-dry sandpaper. Using light

pressure, move the cylinder head in a figure eight

motion. Inspect the sealing surface for any indication

of high spots. A high spot can be noted by a bright

metallic finish. Correct any high spots before assem-

bly by continuing to move the cylinder head in a fig-

ure eight motion until a uniform bright metallic

finish is attained.

Measuring Cylinder Head
Distortion

1. Remove any carbon buildup in the combustion

chamber.

2. Lay a straightedge across the cylinder head; then

using a feeler gauge, check the distortion between

the head and the straightedge.

3. Maximum distortion must not exceed specifications.

YT123

Cleaning/Inspecting Cylinder

1. Wash the cylinder in parts-cleaning solvent.

2. Inspect the cylinder for pitting, scoring, scuffing,

warping, and corrosion. If marks are found, repair

the surface using a cylinder hone.

3. Place the cylinder on the surface plate covered with

#400 grit wet-or-dry sandpaper. Using light pressure,

move the cylinder in a figure eight motion. Inspect

the sealing surface for any indication of high spots.

A high spot can be noted by a bright metallic finish.

Correct any high spots before assembly by continu-

ing to move the cylinder in a figure eight motion

until a uniform bright metallic finish is attained.

CC997

Inspecting Cam Chain Guide

1. Inspect cam chain guide for cuts, tears, breaks, or

chips.

2. If the chain guide is damaged, it must be replaced.

Honing Cylinder

1. Using a slide gauge and a dial indicator or a snap

gauge, measure the cylinder bore diameter in three

locations from top to bottom and again from top to

bottom at 90° from the first measurements for a total

of six measurements. The trueness (out-of-round-

ness) is the difference between the highest and low-

est reading. Maximum trueness (out-of-roundness)

must not exceed specifications.

CC127D

2. Wash the cylinder in parts-cleaning solvent.

3. Inspect the cylinder for pitting, scoring, scuffing, and

corrosion. If marks are found, repair the surface

using a #320 grit ball hone.



NOTE: To produce the proper 60° cross-hatch pat-

tern, use a low RPM drill (600 RPM) at the rate of 30
strokes per minute. If honing oil is not available, use
a lightweight petroleum-based oil. Thoroughly clean
cylinder after honing using soap and hot water. Dry
with compressed air; then immediately apply oil to
the cylinder bore. If the bore is severely damaged or
gouged, replace the cylinder.

CAUTION

Water or parts-cleaning solvent must be used in con-
junction with the wet-or-dry sandpaper or damage to
the sealing surface may result.

CAUTION

Water or parts-cleaning solvent must be used in con-
junction with the wet-or-dry sandpaper or damage to
the sealing surface may result.

«
...
33
34
35
36
37
...
»

Содержание DVX 90/90 UTILITY























































































Отзывы:

Нет отзывов

Похожие инструкции для DVX 90/90 UTILITY

Бренд: Eton America Страницы: 96

Бренд: Taylor-Dunn Страницы: 111

Бренд: Landoll Страницы: 76

Бренд: Craftsman Страницы: 80

Бренд: Linhai Страницы: 92

Trailblazer E2020

Бренд: Evinrude Страницы: 14

Centennial A-130-12R

Бренд: Etnyre Страницы: 20

Бренд: Terra Cat Страницы: 12

Бренд: Erde Страницы: 4

Бренд: Variant Страницы: 16

MARSH MASTER 2015

Бренд: COAST MACHINERY Страницы: 59

Бренд: MULTIQUIP Страницы: 54

Workman 133-0959

Бренд: Toro Страницы: 8

Workman MDE 07299

Бренд: Toro Страницы: 44

Бренд: Toro Страницы: 56

Workman HDX 07383

Бренд: Toro Страницы: 68

Бренд: Snapper Страницы: 4

Бренд: Snapper Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды