manualshive.com logo in svg

Arctic Cat DVX 90/90 UTILITY, Руководство по обслуживанию

Поделиться
Скачать
Arctic Cat DVX 90/90 UTILITY Скачать руководство пользователя страница 4

1

TABLE OF CONTENTS

General Information........................................................... 2

Specifications ............................................................... 2
Torque Specifications.................................................... 3
Torque Conversions (ft-lb/N-m)..................................... 3
Break-In Procedure ...................................................... 3
Gasoline-Oil-Lubricant .................................................. 4
Genuine Parts............................................................... 4
Preparation For Storage ............................................... 4
Preparation After Storage ............................................. 5

Periodic Maintenance/Tune-Up......................................... 6

Periodic Maintenance Chart ......................................... 6
Air Filter ........................................................................ 7
Valve/Tappet Clearance ................................................ 7
Testing Engine Compression ........................................ 8
Spark Plug .................................................................... 9
Muffler/Spark Arrester .................................................. 9
Transmission Lubricant ................................................. 9
Engine Oil ................................................................... 10
Headlights................................................................... 11
Brakelight/Taillight ....................................................... 11
Brake Systems............................................................ 12
Replacing Drive Belt ................................................... 14
Adjusting Shift Linkage ............................................... 15
Troubleshooting Brake System ................................... 15

Steering/Frame/Controls ................................................. 16

Steering Post/Handlebar/Tie Rods ............................. 16
Handlebar Grip ........................................................... 19
Handlebar Switch ....................................................... 19
Hand Brake Lever Assemblies.................................... 20
Troubleshooting .......................................................... 23

Engine/Transmission....................................................... 24

Removing Engine/Transmission ................................. 24
Top-Side Components ................................................ 25
Removing Top-Side Components ............................... 26
Servicing Top-Side Components ................................ 28
Installing Top-Side Components ................................. 33
Left-Side Components ................................................ 36
Removing Left-Side Components............................... 36
Installing Left-Side Components................................. 38
Right-Side Components ............................................. 39
Removing Right-Side Components ............................ 40
Servicing Right-Side Components.............................. 43
Installing Right-Side Components .............................. 44
Center Crankcase Components ................................. 46
Disassembling Crankcase Halves .............................. 46

Servicing Crankcase Components ..............................47
Assembling Crankcase Half ........................................48
Installing Engine/Transmission ....................................49
Troubleshooting ...........................................................51

Fuel/Lubrication................................................................53

Carburetor Schematic .................................................53
Carburetor ...................................................................53
Throttle Cable Free-Play .............................................57
Engine RPM (Idle) .......................................................57
Gas Tank .....................................................................58
Gas Tank Valve ...........................................................59
Gas/Vent Hoses ..........................................................60
Oil Pump Assembly .....................................................60
Oil Screen/Filter ..........................................................60
Troubleshooting ...........................................................60

Electrical System..............................................................61

Battery.........................................................................61
Testing Electrical Components ....................................62
Timing Sensor .............................................................62
CDI/Ignition Coil ..........................................................62
Stator Coil ...................................................................62
Choke Circuit...............................................................63
Brakelight Switch.........................................................63
Fuse ............................................................................63
Ignition Coil .................................................................63
Ignition Switch .............................................................64
Handlebar Control Switches........................................64
Magneto Assembly......................................................64
Starter Motor ...............................................................65
Regulator/Rectifier ......................................................65
Ignition Timing .............................................................65
Headlights ...................................................................65
Troubleshooting ...........................................................65

Drive System.....................................................................67

Drive Chain/Sprockets.................................................67
Rear Hub/Drive Axle....................................................69
Front Hub ....................................................................72
Brake Systems ............................................................73
Troubleshooting ...........................................................74

Suspension .......................................................................75

Shock Absorbers .........................................................75
A-Arm ..........................................................................76
Swing Arm...................................................................78
Wheels and Tires ........................................................80
Troubleshooting ...........................................................81

Содержание DVX 90/90 UTILITY























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды