Arctic Cat DVX 90/90 UTILITY Скачать руководство пользователя страница 79

Страница: 79 / 86

INSTALLING FRONT SHOCK
ABSORBERS

1. Place a shock absorber into position on the frame and

A-arm and install the two cap screws and self-lock-

ing nuts. Tighten the nuts to 29 ft-lb.

MD2131

MD2132

2. Repeat the procedure for the other front shock

absorber.

3. Remove the ATV from the support stand.

INSTALLING REAR SHOCK

ABSORBER

1. Place the spring preload adjuster and spring over the

shock absorber. Compress the spring and install the

retainer.

2. Place the shock absorber into position on the frame

and swing arm and install the two cap screws.

Tighten the cap screws to 29 ft-lb.

MD2314

MD2315

3. Remove the ATV from the support stand.

A-Arm

REMOVING

1. Secure the ATV on a support stand to elevate the

front wheel; then remove the wheel.

2. Remove the cotter pin, castle nut, and washer; then

remove the hub assembly.

MD2133

CAUTION

Do not tighten the nuts beyond the 29 ft-lb specification
or the shock eyelet or mount WILL be damaged.

CAUTION

Do not tighten the cap screws beyond the 29 ft-lb speci-
fication or the shock eyelet or mount WILL be damaged.

! WARNING

Make sure the ATV is solidly supported on the support
stand to avoid injury.

Содержание DVX 90/90 UTILITY























































































Результаты поиска

Содержание DVX 90/90 UTILITY

Отзывы:

Бренды по названию

Популярные бренды

Arctic Cat DVX 90/90 UTILITY, Руководство по обслуживанию

Результаты поиска

Содержание DVX 90/90 UTILITY

Отзывы:

Бренды по названию

Популярные бренды