manualshive.com logo in svg

Arctic Cat DVX 90 2010, Руководство по обслуживанию

Поделиться
Скачать
Arctic Cat DVX 90 2010 Скачать руководство пользователя страница 86

7-9

7

MD2422

CHECKING/INFLATING

1. Using an air pressure gauge, measure the air pres-

sure in each tire. Adjust the air pressure as neces-

sary to meet the specified inflation pressure.

2. Inspect the tires for damage, wear, or punctures.

NOTE: If repair is needed, follow the instructions

found on the tire repair kit or remove the wheel
and have it repaired professionally.

NOTE: Be sure all tires are the specified size and

have identical tread pattern.

3. Test drive the ATV on a dry, level surface and note

any pulling to the left or right during acceleration,

deceleration, and braking.

NOTE: If pulling is noted, measure the circumfer-

ence of the front and rear tires on the pulling side.
Compare the measurements with the tires on the
opposite side. If pulling is noted during braking
only, check and adjust the brakes as necessary
and recheck operation (see Section 2).

4. Increase the air pressure in the tires with the small-

est circumference measurement until all tires are

equal in circumference.

5. Repeat steps 3-4 as necessary to ensure proper

handling.

Troubleshooting

! WARNING

Do not operate the ATV if tire damage exists.

Problem: Suspension too soft

Condition

Remedy

1.

Spring(s)

 weak

2.

Shock absorber

 damaged

1. Replace spring(s)
2. Replace shock absorber

Problem: Suspension too stiff

Condition

Remedy

1.

A-arm bushings

 worn

2.

Shock absorber

 improperly adjusted (rear)

1. Replace bushing
2. Adjust shock spring preload

Problem: Suspension noisy

Condition

Remedy

1.

Cap screws (suspension system)

 loose

2.

A-arm bushings

 worn

1. Tighten cap screws
2. Replace bushings

Problem: Rear wheel oscillation

Condition

Remedy

1.

Rear wheel hub bearings

 worn - loose

2.

Tires

 defective - incorrect

3.

Wheel rim

 distorted

4.

Wheel hub cap screws

 loose

5.

Axle shaft nut

 loose

6.

Rear brake

 adjusted incorrectly

7.

Rear suspension arm-related bushing

 worn

8.

Rear shock absorber

 damaged

9.

Rear suspension arm nut

 loose

1. Replace bearings
2. Replace tires
3. Replace wheel
4. Tighten cap screws
5. Tighten nut
6. Adjust brake
7. Replace bushing
8. Replace shock absorber
9. Tighten nut

Back to TOC

Back to Section TOC

Back

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание DVX 90 2010



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды