manualshive.com logo in svg

Arctic Cat DVX 90 2010, Руководство по обслуживанию

Поделиться
Скачать
Arctic Cat DVX 90 2010 Скачать руководство пользователя страница 85

7-8

MD2014

9. Place the axle housing into position on the swing

arm; then install and tighten four cap screws to 29

ft-lb.

10. Install the brake caliper on the axle housing with

the two cap screws. Tighten securely.

KM229

11. Install the wheels and tighten the cap screws to 30

ft-lb; then remove the ATV from the support stand.

Wheels and Tires

TIRE SIZE

The ATV is equipped with low-pressure tubeless tires of

the size and type listed (see Section 1). Do not under any

circumstances substitute tires of a different type or size.

TIRE INFLATION PRESSURE

Front and rear tire inflation pressure should be 0.21
kg-cm

2

 (3.0 psi).

REMOVING

1. Secure the ATV on a support stand to elevate the

wheels.

2. Remove the four cap screws securing each wheel;

then remove the wheels.

NOTE: Keep left-side and right-side wheels sepa-

rated for installing them on their proper sides.

MD2421

CLEANING AND INSPECTING

NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is
necessary.

1. Clean the wheels and hubs with parts-cleaning sol-

vent.

2. Clean the tires with soap and water.

3. Inspect each wheel for cracks, dents, or bends.

4. Inspect each tire for cuts, wear, missing lugs, and

leaks.

INSTALLING

1. Install each wheel on its hub.

NOTE: Make sure each wheel is installed on its

proper hub as noted in removing (the “rotation
arrow” must indicate forward direction of rotation).

2. Tighten cap screws to 30 ft-lb.

! WARNING

After removing and installing of components that are
brake-related, ALWAYS check and adjust brakes as
necessary before operating the ATV.

! WARNING

Use only Arctic Cat approved tires when replacing
tires. Failure to do so could result in unstable ATV
operation.

! WARNING

Do not mix tire tread patterns. Use the same pattern type
on front and rear. Failure to heed warning could cause
poor handling qualities of the ATV and could cause
excessive drive train damage not covered by warranty.

! WARNING

Always maintain proper tire inflation pressure.

! WARNING

Make sure the ATV is solidly supported on the support
stand to avoid injury.

Back to TOC

Back to Section TOC

Next

Back

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание DVX 90 2010



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды