manualshive.com logo in svg

Arctic Cat DVX 90 2010, Руководство по обслуживанию

Поделиться
Скачать
Arctic Cat DVX 90 2010 Скачать руководство пользователя страница 25

3-7

3

11. Remove the cam chain tensioner pivot bolt; then

remove the chain tensioner.

YT114A

12. Using a needle-nose pliers, remove the circlip

securing the piston pin in the piston; then remove

the piston pin and piston. Take care not to drop the

circlip into the crankcase.

YT115

NOTE: Support the connecting rod with rubber

bands or install a connecting rod holder to avoid
damaging the rod.

NOTE: If the existing rings will not be replaced

with new rings, note the location of each ring for
proper installation. When replacing with new rings,
replace as a complete set only. If the piston rings
must be removed, remove them in this sequence.

Servicing Top-Side 

Components

NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is
necessary.

VALVE ASSEMBLY

When servicing valve assembly, inspect valve seats,

valve stems, valve faces, and valve stem ends for pits,

burn marks, or other signs of abnormal wear.

NOTE: Whenever a valve is out of tolerance, it

must be replaced.

Cleaning/Inspecting Cylinder Head 

Assembly

Inspect the combustion area of the cylinder head for

cracks, burned valves or carbon build-up. 

NOTE: If valves are discolored, they must be

replaced. Arctic Cat recommends taking heads to
a qualified machine shop for valve replacement or
valve seat grinding.

REMOVING VALVES

NOTE: Keep all valves and valve components as

a set. Note the original location of each valve set
for use during installation. Return each valve set
to its original location during installation.

1. Using a valve spring compressor, compress the

valve springs and remove the valve cotters.

Account for an upper spring retainer.

CC391D

2. Remove the valve seal and the lower remaining

spring seat. Discard the valve seal.



AT THIS POINT

To service cylinder, see Servicing Top-Side Compo-
nents sub-section.

CAUTION

When removing the cylinder, be sure to support the
piston to prevent damage to the crankcase and piston.

CAUTION

Do not allow the connecting rod to go down inside the
crankcase. If the rod is down inside the crankcase and
the crankshaft is rotated, severe damage will result.



AT THIS POINT

To service piston, see Servicing Top-Side Compo-
nents sub-section.



AT THIS POINT

To service center crankcase components only, pro-
ceed to Removing Left-Side Components.

Back to TOC

Back to Section TOC

Next

Back

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание DVX 90 2010



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды