manualshive.com logo in svg

Arctic Cat DVX 90 2010, Руководство по обслуживанию

Поделиться
Скачать
Arctic Cat DVX 90 2010 Скачать руководство пользователя страница 37

3-19

3

YT160B

9. Install two alignment pins and the gasket; then

secure the V-belt cover to the crankcase and

tighten the cap screws in a crisscross pattern to 7

ft-lb. Make sure the different-lengthed cap screw

is located as illustrated.

YT099A

Right-Side Components

NOTE: For efficiency, it is preferable to remove

and disassemble only those components which
need to be addressed and to service only those
components. The technician should use discretion
and sound judgment.

NOTE: The engine/transmission does not have to

be removed from the frame for this procedure.

Removing Right-Side 

Components

A. COOLING FAN
B. ROTOR/FLYWHEEL
C. STATOR COIL

D. OIL PUMP

1. Remove the intake pipe/carburetor. Account for an

O-ring in the intake pipe.

2. Remove the cooling fan shroud; then remove the

cooling shroud from the cylinder and cylinder

head.

YT091A

YT092

3. Remove the cooling fan; then remove the nut

securing the rotor/flywheel.

YT029

CAUTION

Failure to fully engage the splines with the kick-start
ratchet could cause false torque reading and crank-
shaft damage.



AT THIS POINT

To service center crankcase components only, pro-
ceed to Removing Right-Side Components. 



AT THIS POINT

To service any one specific component, only limited
disassembly of components may be necessary. Note
the AT THIS POINT information in each sub-section.

Back to TOC

Back to Section TOC

Next

Back

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание DVX 90 2010



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды