manualshive.com logo in svg

Arctic Cat DVX 90 2010, Руководство по обслуживанию

Поделиться
Скачать
Arctic Cat DVX 90 2010 Скачать руководство пользователя страница 16

2-10

MD2044

3. Install the wheel hub, washer, and castle nut.

Tighten the castle nut to 45 ft-lb; then install a new

cotter pin.

4. Install the wheel. Tighten to 30 ft-lb.

5. Repeat this procedure for the other side; then

adjust the brake (see Adjusting Front Wheel Brake

in this sub-section).

6. Remove the ATV from the support stand.

Installing Rear Brake Pads

1. Place the inner pad spring clip into position and

install the inner brake pad; then install the outer

pad onto the holder pins.

KM214

KM222

2. Place the assembled caliper into position on the

disc; then secure with the two cap screws. Tighten

to 22 ft-lb.

NOTE: Always compress the hydraulic brake

lever several times to check that the brakes are
firm. If the brakes are not firm, bleeding the system
will be necessary (see BLEEDING in this sub-sec-
tion).

BLEEDING

To bleed the brake system, use the following proce-

dure.

1. Remove the brake fluid reservoir cover and fill the

reservoir with DOT 4 brake fluid.

2. Install and secure the cover.

3. Remove the protective cap from the bleed screw

and connect one end of a clear hose to the bleed

screw and direct the other end into a suitable con-

tainer.

KM207A

AF637D

4. Slowly compress the brake lever several times;

then while holding slight pressure on the brake

lever, open the bleed screw and watch for air bub-

bles in the hose. Close the bleed screw before

releasing the brake lever. Repeat this procedure

until no air bubbles are present.

NOTE: During the bleeding procedure, watch the

reservoir sight glass to make sure there is always
a sufficient amount of brake fluid in the reservoir.
Failure to maintain sufficient amount of fluid in the
reservoir will result in air being in the system.

5. Repeat step 4 until the brake lever is firm.

Back to TOC

Back to Section TOC

Next

Back

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание DVX 90 2010



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды