manualshive.com logo in svg

Arctic Cat DVX 90 2010, Руководство по обслуживанию

Поделиться
Скачать
Arctic Cat DVX 90 2010 Скачать руководство пользователя страница 80

7-3

7

MD2315

4. Compress the shock absorber spring and remove

the spring retainer. Remove the spring and spring

preload adjuster.

CLEANING AND INSPECTING

NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is
necessary.

1. Clean all shock absorber components.

2. Inspect each shock rod for nicks, pits, rust, bends,

and oily residue.

3. Inspect all springs, spring retainers, shock rods,

dampers, bushings, shock bodies, and eyelets for

cracks, leaks, and bends.

INSTALLING FRONT SHOCK 
ABSORBERS

1. Place a shock absorber into position on the frame

and A-arm and install the two cap screws and

self-locking nuts. Tighten the nuts to 29 ft-lb.

MD2131

MD2132

2. Repeat the procedure for the other front shock

absorber.

3. Remove the ATV from the support stand.

INSTALLING REAR SHOCK 
ABSORBER

1. Place the spring preload adjuster and spring over

the shock absorber. Compress the spring and

install the retainer.

2. Place the shock absorber into position on the

frame and swing arm and install the two cap

screws. Tighten the cap screws to 29 ft-lb.

MD2314

MD2315

CAUTION

Do not tighten the nuts beyond the 29 ft-lb specifica-
tion or the shock eyelet or mount WILL be damaged.

Back to TOC

Back to Section TOC

Next

Back

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание DVX 90 2010



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды