manualshive.com logo in svg

Arctic Cat DVX 90 2010, Руководство по обслуживанию

Поделиться
Скачать
Arctic Cat DVX 90 2010 Скачать руководство пользователя страница 73

6-5

6

Rear Hub/Drive Axle

REMOVING REAR HUB/DRIVE AXLE

1. Secure the ATV on a support stand to elevate the

rear wheels.

2. Remove the cotter pins from the castle nuts on the

rear wheel hubs.

3. Remove the rear wheel hub castle nuts; then slide

the rear wheels and hubs off together. Account for

the washers.

4. Remove the two axle nuts securing the brake hub

to the axle.

YT195A

5. Remove the drive chain (see Removing Drive

Chain sub-section).

6. Remove the rear sprocket (see steps 4-5 of

Removing Rear Sprocket sub-section).

7. Remove the drive axle by sliding it out the right

side of the axle housing.

REMOVING BEARINGS AND SEALS 

1. Secure the ATV on a support stand to elevate the

rear wheels.

2. Remove the wheels and hubs (see Removing Rear

Hub/Drive Axle in this sub-section).

3. Using an appropriate prying tool, carefully pry out

the seals from each side of the axle housing. 

KM232

4. Drive out the bearings from the axle housing.

Account for center axle housing spacer.

REMOVING AXLE HOUSING

1. Secure the ATV on a support stand to elevate the

rear wheels.

2. Remove two cap screws securing the brake caliper

to the axle housing; then lift the caliper off the

disc.

KM207

3. Remove drive chain, wheels, hubs, and axle as

necessary (see Removing Rear Hub/ Drive Axle in

this sub-section).

! WARNING

Make sure the ATV is solidly supported on the support
stand to avoid injury.



AT THIS POINT

If the technician’s objective is to service/replace the
drive axle, the axle housing does not have to be
removed from the swing arm. The axle can be pulled
out the right side of the axle housing. Axle bearings
can also be replaced without removing the axle hous-
ing from the swing arm, but the rear axle housing
cover and brake hub will need to be removed. The axle
housing should only be removed if it needs to be ser-
viced or replaced.

! WARNING

Make sure the ATV is solidly supported on the support
stand to avoid injury.

! WARNING

Make sure the ATV is solidly supported on the support
stand to avoid injury.

Back to TOC

Back to Section TOC

Next

Back

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание DVX 90 2010



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды