Arctic Cat DVX 90 2010 Скачать руководство пользователя страница 39

Страница: 39 / 98

3-21

YT036A

3. Carefully remove the transmission case cover

while pressing in on the output driveshaft and shift

shaft to leave components in the transmission

case. Account for two alignment pins and gasket.

YT038

YT041A



NOTE: The driveshaft thrust washer may be

stuck to the cover. Make sure to install it on the
driveshaft and keep together for assembly.

Disassembling



NOTE: For steps 4-8 refer to illustration YT041B.

4. Remove the output driveshaft (A); then remove

the shift fork shaft (G).

YT041B

5. Remove the main shaft (B) and shift fork together.

Account for the shift fork, a spacer, and a thrust

washer.

YT051

YT042A

6. Remove the countershaft (C). Account for one

thrust washer.

YT043A

Back to TOC

Back to Section TOC

Next

Back

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание DVX 90 2010



































































































Результаты поиска

Содержание DVX 90 2010

Отзывы:

Бренды по названию

Популярные бренды

Arctic Cat DVX 90 2010, Руководство по обслуживанию

Результаты поиска

Содержание DVX 90 2010

Отзывы:

Бренды по названию

Популярные бренды