manualshive.com logo in svg

Arctic Cat DVX 90 2010, Руководство по обслуживанию

Поделиться
Скачать
Arctic Cat DVX 90 2010 Скачать руководство пользователя страница 21

3-3

3

Y-12+

(Table of Contents)

Removing Engine/Transmission.............................. 3-3
Top-Side Components............................................. 3-5
Removing Top-Side Components ........................... 3-5
Servicing Top-Side Components............................. 3-7
Installing Top-Side Components ........................... 3-13
Left-Side Components .......................................... 3-15
Removing Left-Side Components ......................... 3-16
Installing Left-Side Components ........................... 3-17
Right-Side Components ........................................ 3-19
Removing Right-Side Components....................... 3-19
Servicing Right-Side Components ........................ 3-22
Installing Right-Side Components......................... 3-23
Center Crankcase Components............................ 3-26
Disassembling Crankcase Half ............................. 3-26
Servicing Crankcase Half...................................... 3-27
Assembling Crankcase Half .................................. 3-28
Installing Engine/Transmission.............................. 3-29

Removing 

Engine/Transmission

1. Turn the gas tank valve to the OFF position; then

remove the seat and disconnect the negative bat-

tery cable securing it away from the battery.

CD643

KM853A

2. Drain the transmission lubricant. 

NOTE: The drain plug is located on the bottom of

the transmission. 

KM038A

3. Drain the engine oil. 

NOTE: The drain plug is located at the left-rear of

the engine. 

KM041A

4. Remove the left and right footwells and the

left-side footwell mounting plate; then remove the

drive sprocket and chain from the transmission

output shaft.

! WARNING

Battery acid is harmful if it contacts eyes, skin, or cloth-
ing. Care must be taken whenever handling a battery.

Back to TOC

Back to Section TOC

Next

Back

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание DVX 90 2010



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды