manualshive.com logo in svg

Arctic Cat DVX 90 2010, Руководство по обслуживанию

Поделиться
Скачать
Arctic Cat DVX 90 2010 Скачать руководство пользователя страница 36

3-18

YT024B

4. Install the starter countershaft housing; then install

the starter one-way clutch cover. Tighten the cap

screws securely.

YT023A

5. Install the driven pulley/centrifugal clutch assem-

bly onto the transmission input shaft; then install

the centrifugal clutch housing and secure with a

flange nut (coated with red Loctite #271). Tighten

to 40 ft-lb.

YT147

6. Install the movable drive face, bushing, and speed

limiter spacer.

YT164

7. Place the V-belt over the driven pulley; then over

the bushing/spacer. Pinch the belt in the middle to

draw it down into the driven pulley approximately

1 inch.

YT157

YT163A

8. Install the fixed drive face onto the crankshaft and

make sure sufficient splines are protruding to

allow the kick-start ratchet to slide onto the

splines; then install the ratchet (B) and secure with

the flange nut (A) coated with red Loctite #271.

Tighten to 27.5 ft-lb.

Back to TOC

Back to Section TOC

Next

Back

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание DVX 90 2010



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды