Arctic Cat DVX 90 2010 Скачать руководство пользователя страница 76

Страница: 76 / 98

6-8

MD2421

2. Remove the cotter pin from the castle nut.



NOTE: During installing, a new cotter pin should

be installed.

3. Remove the castle nut securing the hub. Account

for a washer.

MD2133

4. Remove the hub assembly. Account for outer hub

spacer.

5. Repeat procedure for other hub.

CLEANING AND INSPECTING



NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is
necessary.

1. Clean all hub components.

2. Inspect all threads for stripping or damage.

3. Inspect the brake shoes for excessive wear or

gouges.

4. Inspect the sealing area of the hub for pits.

5. Inspect the hub splines for signs of wear.

6. Inspect the hub for cracks.

7. Verify that the bearings turn freely.

REMOVING HUB BEARINGS AND
SEALS

1. Carefully pry out inner and outer seals.

MD2385

2. Drive out the inner and outer bearings. Account

for a spacer.

MD2384A

3. Repeat procedure for the other hub.

INSTALLING HUB BEARINGS AND
SEALS

1. Lightly lubricate the bearings with bearing grease;

then using a plastic mallet and a bearing driver or

appropriate size socket, install the inner bearing

into the hub.

MD2382

2. Install the inner hub spacer; then install the outer

bearing.

3. Using a plastic mallet, install the inner and outer

seals into the hub.

Back to TOC

Back to Section TOC

Next

Back

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание DVX 90 2010



































































































Результаты поиска

Содержание DVX 90 2010

Отзывы:

Бренды по названию

Популярные бренды

Arctic Cat DVX 90 2010, Руководство по обслуживанию

Результаты поиска

Содержание DVX 90 2010

Отзывы:

Бренды по названию

Популярные бренды