manualshive.com logo in svg

Arctic Cat DVX 90 2010, Руководство по обслуживанию

Поделиться
Скачать
Arctic Cat DVX 90 2010 Скачать руководство пользователя страница 81

7-4

3. Remove the ATV from the support stand.

A-Arm

REMOVING

1. Secure the ATV on a support stand to elevate the

front wheel; then remove the wheel.

2.  Remove the cotter pin, castle nut, and washer; then

remove the hub assembly.

MD2133

3. Slide brake backing plate assembly off the spindle

shaft and secure it out of the way.

4. Remove the cotter pin from the outer tie rod end;

then while holding the flat on the tie rod end,

remove the castle nut.

MD2428

5. Remove the tie rod end from the steering knuckle.

6. Remove the rubber spindle pin boot; then remove

the cotter pin and flanged castle nut from the spin-

dle pin. Lower the steering knuckle assembly from

the A-arm.

MD2113

7. Remove the cap screw and self-locking nut secur-

ing the shock absorber to the A-arm.

MD2132

8. Remove the cap screws and self-locking nuts

securing the A-arm to the frame.

MD2121

9. Remove the A-arm.

CAUTION

Do not tighten the cap screws beyond the 29 ft-lb
specification or the shock eyelet or mount WILL be
damaged.

! WARNING

Make sure the ATV is solidly supported on the support
stand to avoid injury.

Back to TOC

Back to Section TOC

Next

Back

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание DVX 90 2010



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды