manualshive.com logo in svg

Arctic Cat DVX 90 2010, Руководство по обслуживанию

Поделиться
Скачать
Arctic Cat DVX 90 2010 Скачать руководство пользователя страница 48

3-30

YT008A

YT005A

6. Connect the shift linkage; then install the air filter

housing and air filter. Tighten all hardware

securely.

YT007A

YT003A

7. Connect the starter harness connector (A), stator

coil connector (B), and electric choke connector

(C); then install the spark plug cap.

YT010A

8. Connect the gasline hose (A) to the carburetor;

then connect the crankcase breather hose (B) to the

air filter housing.

YT004A

9. Connect the gear shift position switch connectors

to the main harness and secure to the frame with a

nylon tie.

10. Install the left-side footwell mounting plate to the

frame; then install the left and right footwells and

secure to the mountings and fenders. Tighten all

hardware securely.

11. Pour the recommended quantity of engine oil into

the crankcase; then install the level stick and fill

the transmission with the recommended amount of

gear lubricant. Install the level plug and fill plug.

TR028A

12. Start the engine and check for any fluid leaks.

After a short “test-ride,” shut off the engine and

check the fluid levels. Add fluids as required.

Back to TOC

Back to Section TOC

Next

Back

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание DVX 90 2010



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды