manualshive.com logo in svg

Arctic Cat DVX 90 2010, Руководство по обслуживанию

Поделиться
Скачать
Arctic Cat DVX 90 2010 Скачать руководство пользователя страница 29

3-11

3

ATV-1085B

2. Install the compression rings (1 and 2) so the letter

“T” on the top surface of each ring faces the dome

of the piston. Rotate the rings until the ring end

gaps are on directly opposite sides of the piston

according to the illustration.

NOTE: The chrome (silver) ring should be

installed in the top position.

MD1343C

CYLINDER/CYLINDER HEAD 
ASSEMBLY

NOTE: If the cylinder/cylinder head assembly

cannot be trued, they must be replaced.

Cleaning/Inspecting Cylinder Head

1. Using a non-metallic carbon removal tool, remove

any carbon buildup from the combustion chamber

being careful not to nick, scrape, or damage the

combustion chamber or the sealing surface.

2. Inspect the spark plug hole for any damaged

threads. Repair damaged threads using a

“heli-coil” insert.

3. Place the cylinder head on the surface plate cov-

ered with #400 grit wet-or-dry sandpaper. Using

light pressure, move the cylinder head in a figure

eight motion. Inspect the sealing surface for any

indication of high spots. A high spot can be noted

by a bright metallic finish. Correct any high spots

before assembly by continuing to move the cylin-

der head in a figure eight motion until a uniform

bright metallic finish is attained.

Measuring Cylinder Head 

Distortion

1. Remove any carbon buildup in the combustion

chamber.

2. Lay a straightedge across the cylinder head; then

using a feeler gauge, check the distortion between

the head and the straightedge.

3. Maximum distortion must not exceed specifica-

tions.

YT123

Cleaning/Inspecting Cylinder

1. Wash the cylinder in parts-cleaning solvent.

2. Inspect the cylinder for pitting, scoring, scuffing,

warping, and corrosion. If marks are found, repair

the surface using a cylinder hone (see Honing Cyl-

inder in this sub-section).

3. Place the cylinder on the surface plate covered

with #400 grit wet-or-dry sandpaper. Using light

pressure, move the cylinder in a figure eight

motion. Inspect the sealing surface for any indica-

tion of high spots. A high spot can be noted by a

bright metallic finish. Correct any high spots

before assembly by continuing to move the cylin-

der in a figure eight motion until a uniform bright

metallic finish is attained.

CAUTION

Incorrect installation of the piston rings will result in
engine damage.

CAUTION

Water or parts-cleaning solvent must be used in con-
junction with the wet-or-dry sandpaper or damage to
the sealing surface may result.

CAUTION

Water or parts-cleaning solvent must be used in con-
junction with the wet-or-dry sandpaper or damage to
the sealing surface may result.

Back to TOC

Back to Section TOC

Next

Back

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание DVX 90 2010



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды