manualshive.com logo in svg

Arctic Cat DVX 90 2010, Руководство по обслуживанию

Поделиться
Скачать
Arctic Cat DVX 90 2010 Скачать руководство пользователя страница 1

FOREWORD

This manual contains service, maintenance, and troubleshooting information for the 2010 Arctic Cat Y-12+ Youth

ATV. The manual is designed to aid service personnel in service-oriented applications and may be used as a text-

book for service training.

This manual is divided into sections. Each section covers a specific ATV component or system and, in addition to

the standard service procedures, includes disassembling, inspecting, and assembling instructions. When using this

manual as a guide, the technician should use discretion as to how much disassembly is needed to correct any given

condition. A troubleshooting section is also included in this manual.

The service technician should become familiar with the operation and construction of each component or system

by carefully studying this manual. This manual will assist the service technician in becoming more aware of and

efficient with servicing procedures. Such efficiency not only helps build consumer confidence but also saves time

and labor.

All Arctic Cat ATV publications and decals display the words Warning, Caution, Note, and At This Point to

emphasize important information. The symbol 

! WARNING

 identifies personal safety-related information.

Be sure to follow the directive because it deals with the possibility of severe personal injury or even death. A

CAUTION

 identifies unsafe practices which may result in ATV-related damage. Follow the directive because it

deals with the possibility of damaging part or parts of the ATV. The symbol 

NOTE:

 identifies supplementary

information worthy of particular attention. The symbol 

 

AT THIS POINT

 directs the technician to certain

and specific procedures to promote efficiency and to improve clarity.

At the time of publication, all information, photographs, and illustrations were technically correct. Some photo-

graphs used in this manual are used for clarity purposes only and are not designed to depict actual conditions.

Because Arctic Cat Inc. constantly refines and improves its products, no retroactive obligation is incurred.

All materials and specifications are subject to change without notice.

Keep this manual accessible in the shop area for reference.

Product Service and

Warranty Department

Arctic Cat Inc.

© 2009 Arctic Cat Inc.

July 2009

®™ Trademarks of Arctic Cat Inc., Thief River Falls, MN 56701

Back to TOC

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание DVX 90 2010



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды