Aradex VECTOPOWER VP5000-DC Скачать руководство пользователя страница 150 | Manualshive

Страница: 150 / 173

background image

VP5000-DC/DC60, VP5000-DC/DC200-HL

Operation

Last edited 2019-02-08
by Sonja Scheunert

Filename
VP5000_DCDC60_200-HL_installation_manual_v1-4en.docx

150 / 173

Check the continuous connection of the ground wire system. Measure between the ground wire
connection and the test points of the ground wire system. Check the tight fit and tightening torque
for each ground wire terminal.

7.5.4

Maintenance work: Checking electrical connections

Check the correct tightening torque of the connections.

For a VECTOPOWER VP5000-DC/DC60 see chapter 6.3.8 Installation and commissioning,
Installation, Establishing electrical connections on the VECTOPOWER VP5000-DC/DC60.

For a VECTOPOWER VP5000-DC/DC200-HL see chapter 6.3.9 Installation and commissioning,
Installation, Establishing electrical connections on the VECTOPOWER VP5000-DC/DC200-HL.

7.5.5

Maintenance work: Checking cooling connections

Check the correct tightening torque of the cable glands. See the manufacturer's technical data for
the connections.

7.5.6

Maintenance work: Checking the coolant

Check the coolant for discoloration, turbidity, and odors. Check the mixing ratio. Check whether
the coolant needs to be refilled. See chapter 3.3.8 Product description, Technical data, Data for
cooling.

If necessary, top up or replace the coolant.

Behavior in the event of faults

7.6

If you notice unusual noises or odors, unusual heat generation or anything else unusual,
disconnect the VECTOPOWER from the power supply. Take measures to prevent unauthorized
reconnection. Inform the responsible specialist.

Fault rectification

7.7

7.7.1

Fault rectification procedure

DANGER!

Danger of electric shock, danger from electricity stored in the capacitors

Touching exposed electrical contacts may result in death or serious injury.

•

Only touch the device and the components after you have ensured that they are voltage-
free.

•

Observe the 5 safety rules of electrical engineering.

«
...
148
149
150
151
152
...
»

Содержание VECTOPOWER VP5000-DC














































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VECTOPOWER VP5000-DC

Бренд: Mitsubishi Страницы: 106

Бренд: Parker Страницы: 149

BML-S1G0-B7 Series

Бренд: Balluff Страницы: 20

Бренд: Waeco Страницы: 7

Бренд: Ross Страницы: 2

Бренд: Yarvik Страницы: 64

Бренд: J-Tech Digital Страницы: 5

Smart AC Inverter 100 USB

Бренд: Wagan Страницы: 5

Бренд: T-audio Страницы: 27

Cloudy-Solar Collection IOP-USSS-12V1224-OA Series

Бренд: IO-Power Technology Страницы: 22

NX Distributed Intelligence NX MEDIA CONVERTER

Бренд: Hubbell Страницы: 3

Бренд: ADF Web Страницы: 32

Video 2 Go MP4-P13

Бренд: Laser Страницы: 11

Бренд: Batterytech Страницы: 4

Бренд: Martin Audio Страницы: 51

Бренд: Xantrex Страницы: 112

SoundDock Series II

Бренд: Bose Страницы: 16

Бренд: Ryobi Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды