Aradex VECTOPOWER VP5000-DC Скачать руководство пользователя страница 99

Страница: 99 / 173

VP5000-DC/DC60, VP5000-DC/DC200-HL

Installation and commissioning

Last edited 2019-02-08
by Sonja Scheunert

Filename
VP5000_DCDC60_200-HL_installation_manual_v1-4en.docx

99 / 173

Figure 63: Crane eyes on the housing of the
VECTOPOWER VP5000-DC/DC60

Figure 64: Crane eyes on the housing of the
VECTOPOWER VP5000-DC/DC200-HL

Remove the packaging material from the
VECTOPOWER.

Lift the VECTOPOWER. Use the two upper
crane eyes (1) and suitable lifting gear to
lift it out.

•

The VECTOPOWER has four crane eyes:
one at each corner of the housing.

Figure 65: Mounting points on the housing of the
VECTOPOWER VP5000-DC/DC60

Place the guide holes (2) of the
VECTOPOWER on the two guide pins.

•

On the side of the connections there are
two guide holes (2) next to the mounting
holes, which are open at the bottom.

Slide the VECTOPOWER back onto the
guide pins until it completely rests on the
mounting plate.

Attach the VECTOPOWER to the upper
and lower mounting holes (2)+(3) in two
steps:
In the first step, tighten the screws
crosswise to half the permitted tightening
torque.
In the second step, tighten the screws
crosswise with the maximum permitted

Содержание VECTOPOWER VP5000-DC














































































































































































Результаты поиска

Содержание VECTOPOWER VP5000-DC

Отзывы:

Похожие инструкции для VECTOPOWER VP5000-DC

Бренды по названию

Популярные бренды

Aradex VECTOPOWER VP5000-DC, Руководство по установке

Результаты поиска

Содержание VECTOPOWER VP5000-DC

Отзывы:

Похожие инструкции для VECTOPOWER VP5000-DC

Бренды по названию

Популярные бренды