Analog Devices ADV8005 Скачать руководство пользователя страница 92 | Manualshive

Страница: 92 / 317

background image

UG-707

ADV8005 Hardware Reference Manual

2.2.12.4.

TTL Output CSC

Models of

which provide TTL output now have a CSC in that path, allowing, for example, theTTL output video to be converted to

RGB. The TTL output CSC has the same structure as the primary input CSC but it is limited to a maximum pixel clock frequency of 162MHz.
For higher pixels rates the HDMI TX should be used. The CSC must be manually configured for each color space conversion. The CSC on the
TTL output channel can be enabled using the

ttl_out_csc_enable

control. The CSC mode on the TTL output channel can be configured using

ttl_out_csc_mode[1:0]

. The CSC mode is used to define the fixed point position of the CSC coefficients which are located after

ttl_out_csc_mode[1:0]

in the IO Map for the TTL output channel.

Figure 46 TTL Output Channel CSC

ttl_out_csc_enable

, IO Map,

Address 0x1BB0[7]

This bit is used to enable the ttl output channel CSC.

Function

ttl_out_csc_enable

Description

0 (default)

CSC disable

1

CSC enable

ttl_out_csc_mode[1:0]

, IO Map,

Address 0x1BB0[6:5]

This signal is used to specify the CSC mode for the ttl output channel CSC. The CSC mode sets the fixed point position of the CSC
coefficients, including a4, b4, c4 and offsets.

Function

ttl_out_csc_mode[1:0]

Description

00 (default)

+/- 1.0, -4096 to 4095

01

+/-2.0, -8192 to 8190

10

+/- 4.0, -16384 to 16380

11

+/- 4.0, -16384 to 16380

ttl_out_a1[12:0]

, IO Map,

Address 0x1BB0[4:0]; Address 0x1BB1[7:0]

This signal is used to specify the ttl out channel CSC coefficient A1.

ttl_out_a2[12:0]

, IO Map,

Address 0x1BB2[4:0]; Address 0x1BB3[7:0]

This signal is used to specify the ttl out channel CSC coefficient A2.

ttl_out_a3[12:0]

, IO Map,

Address 0x1BB4[4:0]; Address 0x1BB5[7:0]

This signal is used to specify the ttl out channel CSC coefficient A3.

4x

2x

+

÷

+

+

x

x

x

ttl_out_a1

ttl_out_a2

ttl_out_a3

ttl_out_a4

4096

ttl_out_csc_mode

0

1

2

Out_A

In_A

In_B

In_C

Rev. A | Page 92 of 317

«
...
90
91
92
93
94
...
»

Содержание ADV8005






























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADV8005

Бренд: Moulinex Страницы: 19

Бренд: Scarlett Страницы: 20

Бренд: ARM Страницы: 436

Бренд: Hotpoint Ariston Страницы: 56

Бренд: Hotpoint Ariston Страницы: 134

Бренд: Kiwi Страницы: 18

Бренд: Fastwel Страницы: 53

Бренд: Ecler Страницы: 82

Бренд: DAS AUDIO Страницы: 10

Бренд: Labesto Страницы: 26

Бренд: Omcan Страницы: 24

Бренд: Tesla Страницы: 44

Бренд: Midea Страницы: 11

Бренд: Midea Страницы: 11

Бренд: babymoov Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды