Ammann 5953002 Скачать руководство пользователя страница 43

Страница: 43 / 194

ARX 36-2 T4i, ARX 40-2 T4i , ARX 45-2 T4i

OPERATING MANUAL

2.3.3 Machine depreservation

•

Check all parts of the machine for damage during storage

and for missing parts.

If the machine has been preserved, remove the preserva-

tive agents as follows:
Wash off the preservative agents using a high-pressure

stream of hot water with common degreasers:

Wash the machine while observing environmental

principles.

Caution! Do not use a high-pressure stream to wash

the edge cutter and the highlighted parts of the ma-

chine as shown in Fig. 588589, as this could seriously

damage the machine.

Prevent water from entering the air filter, electrical

and electronic parts of the machine.

Do not use a high-pressure stream near the control

unit!

Use a high-pressure stream at a maximum angle of 90

degrees downwards.

Remove the preservation and wash the machine in plac-

es with intercepting sumps to catch the water and de-

preservation agents.

•

Remove the preservation according to the manufacturer's

manual.

Before putting the machine into operation, check the op-

erating fluids.

Содержание 5953002



































































































































































































Результаты поиска

Содержание 5953002

Отзывы:

Похожие инструкции для 5953002

Бренды по названию

Популярные бренды

Ammann 5953002, Руководство по эксплуатации

Результаты поиска

Содержание 5953002

Отзывы:

Похожие инструкции для 5953002

Бренды по названию

Популярные бренды