Ammann 5953002 Скачать руководство пользователя страница 59

Страница: 59 / 194

ARX 36-2 T4i, ARX 40-2 T4i , ARX 45-2 T4i

OPERATING MANUAL

2635

Hydraulic oil temperature indicator lamp (26)

The hydraulic oil temperature indicator lamp lights up when the

oil temperature exceeds 85 °C.
If the oil temperature exceeds 95 °C, the error F32 will appear.

592520

Emergency stop indicator lamp (27)

The emergency stop indicator lamp lights if the emergency

brake button (6) is enabled.
If the indicator lamp does not go off when the emergency brake

button is disabled, look for the cause!
The engine can be started after the failure has been repaired

and the emergency brake disabled.

595425

Fuel indicator lamp (28)

When the fuel indicator lamp lights up, the tank capacity is suf-

ficient for half-hour operation of the machine.
Refill the fuel!

3518

Engine heating indicator lamp (29)

It indicates the engine warming up before the cold start. The

heating duration is 15 sec.
Start the engine after the indicator lamp has gone out!

AMN58

Error message indicator lamp (22)

The error message indicator lamp lights up when the control

system detects an error. At the same time, the error code ap-

pears on the display.

•

Check the machine according to the table of error message

codes.

•

If the indicator lamp remains lighting, call the service!

2777

Battery charging indicator lamp (23)

When the battery charging indicator lamp lights up during op-

eration or it does not go off after the engine is started, carry out

the undermentioned steps:

•

Stop the engine.

•

Check the V-belt of the engine for damage and loosening. If

the indicator lamp is still lit up when the engine is started,

contact the service centre.

AMN49

Engine lubrication indicator lamp (24)

When the engine lubrication indicator lamp lights up during

operation or does not go off after the engine is started up, you

must stop the machine immediately and turn off the engine!

•

Check the engine for oil leaks and for correct oil level.

•

If the oil level in the engine is correct, call the service!

AMN76

Engine overheating indicator lamp (25)

When the engine overheating indicator lamp lights up during

operation, turn off the engine and refill the coolant! Check the

cooling circuit for leaks! Check the hoses for damage and miss-

ing hose clips.

Содержание 5953002



































































































































































































Результаты поиска

Содержание 5953002

Отзывы:

Похожие инструкции для 5953002

Бренды по названию

Популярные бренды

Ammann 5953002, Руководство по эксплуатации

Результаты поиска

Содержание 5953002

Отзывы:

Похожие инструкции для 5953002

Бренды по названию

Популярные бренды