Ammann 5953002 Скачать руководство пользователя страница 134

Страница: 134 / 194

128

ARX 36-2 T4i, ARX 40-2 T4i , ARX 45-2 T4i

588502

3.6 Lubrication and maintenance operations

3.6.13.3

Check of the service brake

This test verifies the function of the service brake. After activa-

ting the service brake, the hydraulic components of the machi-

ne drive adjust to stop the machine. The service brake can be

controlled at any time. Using the service brake does not activate

the parking brake (P).

Check that the area in front of and behind the machine is

empty and that there are no persons or obstacles there!

Ensure a suitable safe distance in front of the machine,

behind the machine as well as on its sides.
Perform the test on a level and solid surface. If the test

is performed on a slope, the machine may start moving

due to leaking hydraulics even though the service brake

is in order!

Procedure

Place the machine on a flat and solid surface.
Sit in the driver’s position and start the engine according to

Chapter 2.7.1.
Move off by setting the travel control (11) to the forward travel

position “F”.
Set the travel control to the neutral position “N”.
The machine will stop and the parking brake will not activate.
To move off again or control the brake during braking, move the

travel control (11) back to the forward travel position “F”.
If the machine does not stop, activate the emergency brake, se-

cure the machine against spontaneous movement using wed-

ges on a level and solid surface and contact service.

Activation of the emergency brake will cause a high me-

chanical and hydraulic load of the machine. Always test

the parking brake after activating the emergency brake

while driving.

Содержание 5953002



































































































































































































Результаты поиска

Содержание 5953002

Отзывы:

Ammann 5953002, Руководство по эксплуатации, Страница: 134 / 194

Результаты поиска

Содержание 5953002

Отзывы: