manualshive.com logo in svg

Amazone Precea 3000-A, Оригинальное руководство по эксплуатации

Поделиться
Скачать
Amazone Precea 3000-A Скачать руководство пользователя страница 91

NOTE

Position 

P

 is only needed for parking the

implement.

The setting lever 

2

 can also be engaged in half-

steps 

1

 in the grid.

1.

Lift the implement.

2.

Secure the tractor and implement.

3.

Unlock the setting lever.

NOTE

Beyond depth positions F-G, the contact force
regulation is without function.

4.

To use the coulter pressure control,

see "Configuring the coulter pressure monitoring"
in the ISOBUS operating manual.

5.

To increase the seed placement depth,

move the setting lever towards 

G

or

To reduce the seed placement depth,

move the setting lever towards 

A

.

6.

Lock the setting lever in the grid.

7.

To check the setting,

drive for 30 m at working speed and "check the
seed placement depth".

CMS-I-00001919

6 | Preparing the machine

Preparing the implement for operation 

MG6659-EN-GB | F.1 | 25.10.2022 | © AMAZONE

85

Содержание Precea 3000-A







































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды