manualshive.com logo in svg

Amazone Precea 3000-A, Оригинальное руководство по эксплуатации

Поделиться
Скачать
Amazone Precea 3000-A Скачать руководство пользователя страница 127

14. lower the implement.

The depth control wheels 

3

 are resting on the

transport dolly.

15. Hook the belts 

1

 onto the coulter.

16. Remove the bolts 

1

.

17. Remove the coulter bracket 

2

.

CMS-I-00004135

18. Continue lowering the implement.

The coulter 

1

 tips forward.

19. Release the tilted coulter from the frame 

2

.

CMS-I-00005133

20.

To move the remaining coulters to the desired
position,

Loosen the bolts 

1

.

21. Push the coulters into the desired position.

22.

For telescopic coulters

Tighten the bolts to 160 Nm minus 180°,

or

For non-telescopic coulters

Tighten the bolts to 200 Nm.

23. Connect the ISOBUS to the tractor.

CMS-I-00002039

6 | Preparing the machine

Preparing the implement for operation 

MG6659-EN-GB | F.1 | 25.10.2022 | © AMAZONE

121

Содержание Precea 3000-A







































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды