manualshive.com logo in svg

Amazone Precea 3000-A, Оригинальное руководство по эксплуатации

Поделиться
Скачать
Amazone Precea 3000-A Скачать руководство пользователя страница 61

6.

Clean the cover seal and sealing surface 

2

.

7.

Close the hopper cover 

1

.

The fastener 

3

 is locked.

8.

Close the fastener.

CMS-I-00001889

6.3.3 Filling the fertiliser hopper

6.3.3.1 Filling the fertiliser hopper via the loading board

NOTE

The guard screen and function screen in the
fertiliser hopper are closed. Only a closed guard
screen and function screen can prevent fertiliser
clumps and/or foreign objects from entering the
fertiliser hopper and clogging the metering unit.

REQUIREMENTS

The transport vehicle carrying the fertiliser is
standing on a level surface

1.

Determine the payload of the implement and
axles loads of the tractor.

2.

Couple the implement to the tractor.

3.

Secure the tractor and implement.

4.

When working at night, switch on the interior
lighting of the fertiliser hopper.

5.

Climb onto the loading board using the steps.

or

To unfold the ladder,

see "Operating the loading board with ladder".

CMS-T-00001910-F.1

CMS-T-00001911-D.1

6 | Preparing the machine

Preparing the implement for operation 

MG6659-EN-GB | F.1 | 25.10.2022 | © AMAZONE

55

Содержание Precea 3000-A







































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды