manualshive.com logo in svg

Amazone Precea 3000-A, Оригинальное руководство по эксплуатации

Поделиться
Скачать
Amazone Precea 3000-A Скачать руководство пользователя страница 72

6.3.7 Setting up the speed sensor on the implement

To start the metering unit or the electronic monitoring,
a speed signal is required. The speed sensor on the
implement can be used for this.

1.

Set up the speed sensor on the implement.

2.

See "Determining the pulses per 100 m" in the
control computer operating manual

or

See ISOBUS operating manual "Setting up the
speed sensor on the implement".

6.3.8 Using the multi-placement tester

6.3.8.1 Determining the grain size

Determine the grain size of the seed with the multi-
placement tester.

1.

Put the seed in the reference holes 

1

.

2.

If the seed lies loosely on the reference hole,

read the hole diameter.

1

CMS-I-00001217

CMS-T-00001908-C.1

CMS-T-00005293-C.1

CMS-T-00001888-C.1

6 | Preparing the machine

Preparing the implement for operation 

MG6659-EN-GB | F.1 | 25.10.2022 | © AMAZONE

66

Содержание Precea 3000-A







































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды