Altera Arria V GZ Скачать руководство пользователя страница 165

Страница: 165 / 300

Chapter 7: Register Descriptions

7–7

Altera-Defined Vendor Specific Extended Capability (VSEC)

November 2012

Altera Corporation

Arria V GZ Hard IP for PCI Express

User Guide

Table 7–13

defines the

JTAG Silicon ID

registers.

Table 7–14

defines the

User Device or Board Type ID

Table 7–15

defines the fields of the

CvP Status

to monitor the CvP status signals.

Table 7–16

defines the fields of the CvP Mode Control register which provides global

control of the CvP operation.

Table 7–13. JTAG Silicon ID

Bits

Register Description

Value

Access

[127:96]

JTAG Silicon ID DW3

TBD

[95:64]

JTAG Silicon ID DW2

TBD

[63:32]

JTAG Silicon ID DW1

TBD

[31:0]

JTAG Silicon ID DW0

- This is the JTAG Silicon ID that CvP programming

software reads to determine to that the correct SRAM object file (

.sof

) is being

used.

TBD

Table 7–14. User Device or Board Type ID

Bits

Register Description

Value

Access

[15:0]

Configurable device or board type ID to specify to CvP the correct

.sof

. Variable

Table 7–15. CvP Status

Bits

Register Description

Reset Value

Access

[15:10]

Reserved.

0x00

[9]

PLD_CORE_READY

. From FPGA fabric. This status bit is provided for debug.

Variable

[8]

PLD_CLK_IN_USE

. From clock switch module to fabric. This status bit is

provided for debug.

Variable

[7]

CVP_CONFIG_DONE

. Indicates that the FPGA control block has completed the

device configuration via CvP and there were no errors.

Variable

[6]

CVP_HF_RATE_SEL

. Indicates if the FPGA control block interface to the Arria V

GZ hard IP for PCI Express is operating half the normal frequency–62.5MHz,
instead of full rate of 125MHz

Variable

[5]

USERMODE

. Indicates if the configurable FPGA fabric is in user mode.

Variable

[4]

CVP_EN

. Indicates if the FPGA control block has enabled CvP mode.

Variable

[3]

CVP_CONFIG_ERROR

. Reflects the value of this signal from the FPGA control

block, checked by software to determine if there was an error during
configuration

Variable

[2]

CVP_CONFIG_READY – reflects the value of this signal from the FPGA control
block, checked by software during programming algorithm

Variable

[1]

Reserved.

—

[0]

Reserved.

—

Содержание Arria V GZ













































































































































































































































































































Результаты поиска

Содержание Arria V GZ

Отзывы:

Похожие инструкции для Arria V GZ

Бренды по названию

Популярные бренды

Altera Arria V GZ, Руководство пользователя

Результаты поиска

Содержание Arria V GZ

Отзывы:

Похожие инструкции для Arria V GZ

Бренды по названию

Популярные бренды