Altera Arria V GZ Скачать руководство пользователя страница 130 | Manualshive

Страница: 130 / 300

background image

6–36

Chapter 6: IP Core Interfaces

Transaction Layer Configuration Space Signals

Arria V GZ Hard IP for PCI Express

November 2012

Altera Corporation

Table 6–14

describes the bits of the bits of the

tl_cfg_sts

bus.

hpg_ctrler[4:0]

I

The

hpg_ctrler

signals are only available in Root Port mode and when the

Slot capability

is enabled. Refer to the

Slot capability register

parameters in

Table 4–10 on page 4–10

. For Endpoint variations the

hpg_ctrler

input should be

hardwired to 0s. The bits have the following meanings:

I

■

[0]: Attention button pressed. This signal should be asserted when the attention button is
pressed. If no attention button exists for the slot, this bit should be hardwired to 0, and the

Attention Button Present

bit (bit[0]) in the

Slot capability register

parameter is set to

0.

I

■

[1]: Presence detect. This signal should be asserted when a presence detect circuit
detects a presence detect change in the slot.

I

■

[2]: Manually-operated retention latch (MRL) sensor changed. This signal should be
asserted when an MRL sensor indicates that the MRL is Open. If an MRL Sensor does not
exist for the slot, this bit should be hardwired to 0, and the

MRL Sensor Present

bit

(bit[2]) in the

Slot capability register

parameter is set to 0.

I

■

[3]: Power fault detected. This signal should be asserted when the power controller
detects a power fault for this slot. If this slot has no power controller, this bit should be
hardwired to 0, and the

Power Controller Present

bit (bit[1]) in the

Slot capability

parameter is set to 0.

I

■

[4]: Power controller status. This signal is used to set the command completed bit of the

Slot

Status

register. Power controller status is equal to the power controller control

signal. If this slot has no power controller, this bit should be hardwired to 0 and the

Power

Controller Present

bit (bit[1]) in the

Slot capability register

is set to 0.

Table 6–13. Configuration Space Signals (Hard IP Implementation) (Part 2 of 2)

Signal

Dir

Description

Table 6–14. Mapping Between tl_cfg_sts and Configuration Space Registers (Part 1 of 2)

tl_cfg_sts

Configuration Space Register

Description

[52:49]

Device Status Register[3:0]

Records the following errors:

■

Bit 3: unsupported request detected

■

Bit 2: fatal error detected

■

Bit 1: non-fatal error detected

■

Bit 0: correctable error detected

[48]

Slot Status Register[8]

Data Link Layer state changed

[47]

Slot Status Register[4]

Command completed. (The hot plug controller completed a
command.)

[46:31]

Link Status Register[15:0]

Records the following link status information:

■

Bit 15: link autonomous bandwidth status

■

Bit 14: link bandwidth management status

■

Bit 13: Data Link Layer link active

■

Bit 12: Slot clock configuration

■

Bit 11: Link Training

■

Bit 10: Undefined

■

Bits[9:4]: Negotiated Link Width

■

Bits[3:0] Link Speed

«
...
128
129
130
131
132
...
»

Содержание Arria V GZ













































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Arria V GZ

Бренд: SENAO Страницы: 26

Бренд: Gigabyte Страницы: 38

iCLASS SE Biometric Reader

Бренд: HID Страницы: 50

Бренд: ACS Страницы: 7

Бренд: ADLINK Technology Страницы: 53

Бренд: Diablotek Страницы: 1

Бренд: RealTrace Страницы: 2

Бренд: RocketFish Страницы: 2

9800GT 512MB GREEN EDITION

Бренд: Gainward Страницы: 2

Бренд: V.TOP Страницы: 9

PCIE-5565RC Series

Бренд: ABACO Страницы: 72

ACTpro MIFARE Classic MF1030e

Бренд: Vanderbilt Страницы: 17

VR1 S-MF Series

Бренд: Vanderbilt Страницы: 24

Бренд: Vanderbilt Страницы: 30

Бренд: Oracle Страницы: 56

Бренд: IBC Страницы: 7

PCI-DIO48 Series

Бренд: ICS Advent Страницы: 32

Бренд: CAMDEN Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды