manualshive.com logo in svg

Altera Arria V GZ, Руководство пользователя

На нашем сайте вы можете бесплатно скачать руководство пользователя для продукта Altera Arria V GZ. Это подробное руководство поможет вам быстро и легко разобраться с устройством. Скачать его можно на manualshive.com.

Поделиться
Скачать
background image

Chapter 2: Getting Started with the Arria V GZ Hard IP for PCI Express

2–13

Qsys Design Flow

November 2012

Altera Corporation

Arria V GZ Hard IP for PCI Express

User Guide

Example 2–1. Excerpts from Transcript of Successful Simulation Run (continued)

 
# INFO:            8973 ns  RP LTSSM State: CONFIG.LANENUM.WAIT                                                                
# INFO:            9537 ns  EP LTSSM State: CONFIG.LANENUM.WAIT                                                                
# INFO:            9857 ns  EP LTSSM State: CONFIG.LANENUM.ACCEPT                                                              
# INFO:            9933 ns  RP LTSSM State: CONFIG.LANENUM.ACCEPT                                                              
# INFO:           10189 ns  RP LTSSM State: CONFIG.COMPLETE                                                                    
# INFO:           10689 ns  EP LTSSM State: CONFIG.COMPLETE                                                                    
# INFO:           12109 ns  RP LTSSM State: CONFIG.IDLE                                                                        
# INFO:           13697 ns  EP LTSSM State: CONFIG.IDLE                                                                        
# INFO:           13889 ns  EP LTSSM State: L0                                                                                 
# INFO: 

 13981 ns  RP LTSSM State: L0 

# INFO:           17800 ns Configuring Bus 001, Device 001, Function 00                                                        
# INFO:           17800 ns   EP Read Only Configuration Registers:                                                             
# INFO:           17800 ns                 Vendor ID: 1172                                                                     
# INFO:           17800 ns                 Device ID: E001                                                                     
# INFO:           17800 ns               Revision ID: 01                                                                       
# INFO:           17800 ns                Class Code: FF0000                                                                   
# INFO:           17800 ns       Subsystem Vendor ID: 1172                                                                     
# INFO:           17800 ns              Subsystem ID: E001                                                                     
# INFO:           17800 ns             Interrupt Pin: INTA# used                                                               
# INFO:           17800 ns                                                                                                     
# INFO:           20040 ns   PCI MSI Capability Register:                                                                      
# INFO:           20040 ns    64-Bit Address Capable: Supported                                                                
# INFO:           20040 ns        Messages Requested:  4                                                                       
# INFO:           20040 ns                                                                                                     
#INFO:           31208 ns   EP PCI Express Link Status Register (1081):                                                       
# INFO:           31208 ns     Negotiated Link Width: x8                                                                       
# INFO:           31208 ns         Slot Clock Config: System Reference Clock Used                                              
# INFO:           33481 ns  RP LTSSM State: RECOVERY.RCVRLOCK                                                                  
# INFO:           34321 ns  EP LTSSM State: RECOVERY.RCVRLOCK                                                                  
# INFO:           34961 ns  EP LTSSM State: RECOVERY.RCVRCFG                                                                   
# INFO:           35161 ns  RP LTSSM State: RECOVERY.RCVRCFG                                                                   
# INFO:           36377 ns  RP LTSSM State: RECOVERY.IDLE                                                                      
# INFO:           37457 ns  EP LTSSM State: RECOVERY.IDLE                                                                      
# INFO:           37649 ns  EP LTSSM State: L0                                                                                 
# INFO:           37737 ns  RP LTSSM State: L0                                                                                 
# INFO:           39944 ns        Current Link Speed: 2.5GT/s                                                                  
# INFO:           58904 ns Completed configuration of Endpoint BARs.                                                           
# INFO:           61288 ns ---------                                                                                           
# INFO:           61288 ns TASK:chained_dma_test                                                                               
# INFO:           61288 ns    DMA: Read                                                                                        
# INFO:           61288 ns ---------                                                                                           
# INFO:           61288 ns TASK:dma_rd_test                                                                                    
# INFO:           61288 ns ---------                                                                                           
# INFO:           61288 ns TASK:dma_set_rd_desc_data                                                                           
# INFO:           61288 ns ---------                                                                                           
# INFO:           61288 ns TASK:dma_set_msi READ                                                                               
# INFO:           61288 ns  Message Signaled Interrupt Configuration                                                           
# INFO:           61288 ns   msi_address (RC memory)= 0x07F0                                                                   
# INFO:           63512 ns   msi_control_register = 0x0084                                                                     
# INFO:           72440 ns   msi_expected = 0xB0FC                                                                             
# INFO:           72440 ns   msi_capabilities address = 0x0050                                                                 
# INFO:           72440 ns   multi_message_enable = 0x0002                                                                     
# INFO:           72440 ns   msi_number = 0000                                                                                 
# INFO:           72440 ns   msi_traffic_class = 0000                                                                          
# INFO:           72440 ns ---------                                                                                           
# INFO:           72440 ns TASK:dma_set_header READ                                                                            

Содержание Arria V GZ













































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Arria V GZ

Digital Equipment EtherWORKS Turbo PCI User Information preview
EtherWORKS Turbo PCI
Бренд: Digital Equipment Страницы: 48
Ansel MIMO PCI 2614 Manual preview
MIMO PCI 2614
Бренд: Ansel Страницы: 41
SIIG SC-SAE012-S2 Quick Installation Manual preview
SC-SAE012-S2
Бренд: SIIG Страницы: 12
Creative Live! PLATINUM 5.1 Product Manual preview
Live! PLATINUM 5.1
Бренд: Creative Страницы: 197
LG CNS SafezoneXID-500 Instruction Manual preview
SafezoneXID-500
Бренд: LG CNS Страницы: 33
Asus Xonar DS User Manual preview
Xonar DS
Бренд: Asus Страницы: 54
Asus PCI Express Audio Card Xonar DX User Manual preview
PCI Express Audio Card Xonar DX
Бренд: Asus Страницы: 80
Asus MIO User Manual preview
MIO
Бренд: Asus Страницы: 2
Asus PCI-AV264CT-N User Manual preview
PCI-AV264CT-N
Бренд: Asus Страницы: 64
Asus Xonar DGX User Manual preview
Xonar DGX
Бренд: Asus Страницы: 58
Asus XONAR DG User Manual preview
XONAR DG
Бренд: Asus Страницы: 58
Asus PCI-V264VT User Manual preview
PCI-V264VT
Бренд: Asus Страницы: 16
Asus Audio Card Xonar D2X User Manual preview
Audio Card Xonar D2X
Бренд: Asus Страницы: 88
Asus Strix Raid DLX User Manual preview
Strix Raid DLX
Бренд: Asus Страницы: 27
Asus PCI-AS300 User Manual preview
PCI-AS300
Бренд: Asus Страницы: 42
Asus Audio Card Xonar D2X Quick Installation Manual preview
Audio Card Xonar D2X
Бренд: Asus Страницы: 70
Contec FX-DS540-MPCI4W User Manual preview
FX-DS540-MPCI4W
Бренд: Contec Страницы: 5
BITMAIN Sophon SC1 User Manual preview
Sophon SC1
Бренд: BITMAIN Страницы: 7

Бренды по названию

Популярные бренды

Загрузить еще бренды