Alpha-InnoTec HT 12Split Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 80

Alpha-InnoTec HT 12Split Скачать руководство пользователя страница 46

46

HT 6Split

HT 12Split

Chapter 9 |

Control

CAUTION

When the heating/cooling sensors BT74 have been
connected and activated in menu 5.4, no other sensor
can be selected in menu 1.9.5.

CAUTION

The point offset can only be edited by qualified per

-

sonnel.

CAUTION

Curve 0 in menu 1.9.1 must be selected in order for “My
curve” to apply.

CAUTION

“My curve” may only be edited by qualified persons.

Menu 1.9.5 - Cooling operation settings

Menu 1.9.7 - My curve

heat./cool. sensor

An extra temperature sensor can be connected to the

heat pump in order to determine when it is time to
switch between heating and cooling operations.
When several heating/cooling sensors are installed,
you can select which one of them should be in control.

start active cooling

Here you can set when active cooling is to start. Degree
minutes are a measurement of the current heating de-
mand in the house and determine when the compres-
sor, cooling operation or additional heat will be started/
stopped.

In this menu, you can create your own heating or
cooling curve by setting the desired supply tempera-

tures for different outdoor temperatures.

HT 6Split / HT 12Split can be used to cool the house
during hot periods of the year. For more information

select "?".

Factory settings:

Delta at +20 C.: 3 °C

Delta at +40 C.: 6 °C

Heat./cool. sensor: N/A

Alarm - room sens. cooling: deactivated

Start active cooling 30 DM

Time betw. switch heat/cool: 2 hours

Menu 1.9.8 - Point offset

Changes to the heating curve at a certain outdoor
temperature are selected here. One step is usual-
ly enough to change the room temperature by one
degree, but in some cases several steps may be re-
quired.

The heating curve is affected at ± 5 °C from the set

outdoor temperature point.

It is important that the correct heating curve is selected
so that the room temperature is experienced as con-

stant. For more information select "?".

Menu 2 - HOT WATER

The hot water menu is used for adjusting hot water
settings. The user can edit temperatures and operat-
ing modes for hot water. Within this menu there are
several submenus. Status information for the relevant
menu can be found on the display to the right of the
menus.

Activation of a temporary increase in the hot water

temperature. Status information reads “off”, or the du

-

ration of the temporary increase in temperature. For

more information select "?".

Factory settings: off

When hot water demand has temporarily increased, this
menu can be used to select an increase in the hot water

temperature to luxury mode for a specified time.

Menu 2.1 - Temporary lux.

«
...
44
45
46
47
48
...
»

Содержание HT 12Split

















































































Отзывы:

Нет отзывов