ALLEN & HEATH iLive-T Series Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 107

background image

iLive Reference Guide – Firmware

Part 2 - 33

AP6526-2 iss.4

Back Panel view - Configure the FX routing

Touch the top right Back Panel button to open up the connections view. This
emulates patching up a typical outboard effects rack. Configure the FX device
as a send/return loop or inserted into a channel or mix signal path.

FX configuration

Choose an option from the drop down menu:

Not Assigned

The FX is not patched.

Insert

The FX is inserted into a channel or mix signal path. Choose

type from the list in the drop down menu and number from the box.

The

Dual Mono

mode allows a stereo effects device such as a chorus

unit to be used on a stereo keyboard connected into two mono
channels as opposed to a stereo channel.

Touch

Apply

to confirm. The lower part of the screen provides the IN

(bypass) button, Dry / Wet balance control, and input / output meters

for the FX.

Mix>Return

This configures the FX as a ‘system effect typical of the

aux send, channel return loop used in live mixing for reverb and delay
effects. Touch Apply to confirm. The lower part of the screen
provides the send and return master controls together with input and
output metering. Note that these controls are also available on the

fader control strips if assigned to them.

Patch from

If configured as a Mix>Return FX then use this drop down

menu to choose which signal sends to the FX input:

Dedicated FX mix bus
Mono or Stereo Aux mix

Channel Direct Output

Note:

The Direct Output selection follows its global setting

configured in the

MIXRACK SETUP / Mixer Pref / Direct Output

page.

As an FX source this would typically be set to Follow Fader

and Follow Mute.

Patch to

If configured as a Mix>Return FX then use this drop down menu

to choose where the return from the FX routes to:

Dedicated stereo FX short return

Mono or stereo full IP channel

FX configuration

Send to the FX

(FX input)

Return from the FX

(FX output)

Apply the

change

Send/Return
masters or Wet/Dry
controls depending

on configuration

«
...
31
32
33
34
35
...
»

Содержание iLive-T Series












































































































Отзывы:

Нет отзывов

Похожие инструкции для iLive-T Series

Бренд: MadBoy Страницы: 36

Бренд: HAI Страницы: 1

Бренд: Radio Shack Страницы: 12

Бренд: Behringer Страницы: 15

HANDMIXER-SET HM 3814

Бренд: SEVERIN Страницы: 1

CHM-7PK - PowerSelect Hand Mixer

Бренд: Cuisinart Страницы: 24

Бренд: Gemini Страницы: 9

Бренд: JB Systems Страницы: 17

DJM-400 - CDJ-400 Package

Бренд: Pioneer Страницы: 16

Бренд: Pioneer Страницы: 28

Бренд: Pioneer Страницы: 44

DJM-400 - CDJ-400 Package

Бренд: Pioneer Страницы: 92

Бренд: Pioneer Страницы: 100

Бренд: Pioneer Страницы: 100

Бренд: Pioneer Страницы: 204

Бренд: Pioneer Страницы: 224

Бренд: Pioneer Страницы: 2

Бренд: Pioneer Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды