ALGE-Timing TDC8001, Руководство пользователя

Страница: 110 / 112

Manual
TdC 8001
-110-
8.4 Display Board (e) – Interface for Display Board
Output format
: 1 start bit, 8 data bit, no parity bit, 1 stop bit
Transfer rate
: standard 2,400 baud (adjustable 4800, 9600, 19200)
Transfer protocol
: ASCII
The display board interface has two different channels
channel 1: running time
channel 2: running time and ranking or stopped time and ranking
Attention: Channels 1 and 2 can be switched by turning the plug at jack (e) by 180°.
Output at channel 1 is always the same as shown on displays (7) and (8). The set display times (menu4)
apply for display (7) and (8) as well as for channel 1 of the display board interface (e). No ranking is
sent.
In channel 2 of the main menu (menu 20) can be switched between running and stopped time. The
ranking is always transferred at channel 2.
NNN.xxxxxxxxM:SSxxxx(CR) running time (without 1/10 seconds)
NNN.xxxxHH.MM.SSxxxx(CR)
running time (without 1/10 seconds)
NNN.xxxxHH:MM:SS.zxx(CR) running time (with 1/10 seconds)
NNNCxxxxHH:MM:SS.zhtRR(CR) channel C1 finish time with rank
NNNCxxxxHH:MM:SS.zhtxx(CR)
channel C1 finish time without rank
NNNDxxxxHH:MM:SS.zhtRR(CR) channel C1 total time with rank
NNNDxxxxHH:MM:SS.zhtxx(CR)
channel C1 total time without rank
NNNAxxxxHH:MM:SS.zhtRR(CR) channel C2 1
st
intermediate time
NNNBxxxxHH:MM:SS.zhtRR(CR) channel C3 2
nd
intermediate time
NNNExxxxHH:MM:SS.zhtRR(CR) channel C4 3
rd
intermediate time
NNNFxxxxHH:MM:SS.zhtRR(CR) channel C5 4
th
intermediate time
NNNGxxxxHH:MM:SS.zhtRR(CR) channel C6 5
th
intermediate time
NNNHxxxxHH:MM:SS.zhtRR(CR) channel C7 6
th
intermediate time
NNNIxxxxHH:MM:SS.zhtRR(CR)
channel C8 7
th
intermediate time
NNNJxxxxHH:MM:SS.zhtRR(CR) channel C9 8
th
intermediate time
NNNSxxx©xxxxsxss.ssxRR(CR) speed
ANNNxxxxxHH:MM:SS.zhtRR(CR) sequential time for program split sequential
NNN ...................... start number (hundreds, tens and units, digits 1 to 3)
. ............................. dot on the fourth digit is the identification for a running time
A,B,C ...,H,I,J ........ address for display board (digit 1)
A,B,C, ...,H,I,J ....... identification of channel (4
th
digit)
© ............................ speed measurement: output fo following ASCII characters:
01 hex for km/h, 02 hex for m/s, 03 hex for mph
RR ......................... rank
x ............................ blank
(CR) ...................... carriage return
Plug assignment: see
cable from TdC 8001 to display board GAZ5: 010-10
cable from TdC 8001 to Teledata TED-TX with power supply: 107-10
In the main menua the following setting can be made for this interface
D-Board time 1 Menu 4 Default = 3 seconds
A time can be set that indicates for how long a stopped time (e. g. intermediate time, run time) remains
on display (5) and display board before the running time is shown once again. This time is called display
time 1. It can be set between 0 and 99 seconds.
Menu 4: DISPLAY TIME 1 = 03 S enter seconds with finish keypad (8)
Save with: ENTER exit with <ENTER>