2
Installation & Commissioning Guide PKY470-700 Tri-Capacity Package with CM100 Control
Doc. No.0525-032
Ver. 9 180921
UNPACKING & INSPECTION
1. Remove the packaging around the unit.
2. Remove anchor bolts between the unit and the pallet.
3. Check the unit components for any sign of transport damage:
• Check for obvious panel dents.
• Check for any dents or breakage in
propeller and blower fan.
If there is any damage to the unit contact ActronAir immediately on toll free number:
1800 119 229
.
• Conduct pull test on all wire terminals.
• Check for loosened screws.
SAFETY PRECAUTIONS
control power supply. Care must be taken to ensure
both are safely isolated to prevent personal injury and
damage to the equipment.
7.
Beware of rotating fans. Long hair, dangling items,
such as clothing and jewellery could become
entangled and pulled into the device.
8. Always use PPE for safety and protection.
9.
Make sure that safety guards and panel covers are
always firmly secured and not damaged.
10. This appliance is not intended for use by young
children or infirm person unless they have been
adequately supervised by a responsible person to
ensure that they can use the appliance safely. Young
children should be supervised to ensure that they do
not play with the appliance.
11.
WH&S rules and regulations must be observed and
will take precedent during installation process.
1.
To ensure proper equipment operation, read all
instructions thoroughly before proceeding with
installation. Failure to do so may result in damage to
the unit and void your warranty.
2.
Installation must be carried out by qualified technician
*
.
3.
Ensure that unit installation complies with relevant
council regulations and building code standards.
4. All electrical wiring must be in accordance with
current electrical authority regulations and all wiring
connections to be as per electrical diagram provided.
5.
This unit is fitted with EC Motors with high power
capacitors, which can have dangerous voltages at
terminals for up to 5 minutes after main power has
been isolated. Wait at least 5 minutes after power
isolation and test for high voltage before performing
service work.
6.
EC Plug Fan fitted to this unit has dual power supplies,
i.e. 415V / 3Ph / 50Hz motor power supply plus 10VDC
*
Qualifications required will be appropriate Electrical, Refrigeration
and Refrigerant Handling License & Training, dependent on local
State/Territory regulations.
TABLE OF CONTENTS
Return Air - Outside Air - Spill Air
Control Wiring Procedures ..........................................
Demand Response Management ...............................
3rd Party Control Connection Diagrams ......................
Compressors and Indoor fans Modes of Operation ....
Menu Tree ...................................................................
Setting Economy Air via Control Interface ...................
Service Password .......................................................
Room Air Temp Sensor Install / Adjustment ................
Various Room Temperature Sensor Connections .......
After Hours Logic with Timeclock (Scheduler) ............
Enable / Disable Air Filter Alarm ..................................
Indoor Fan Speed Setting Procedure .........................
Fan Performance Data & Fan Curve ...........................
Refrigerant Charging ...................................................
Fault Display Codes ....................................................
Alarm Matrix ................................................................
Troubleshooting Guide ................................................
Maintenance ................................................................
Sensors Detail .............................................................
Key Parts List ..............................................................
Start Up & Commissioning Report ..............................
29
30
31
35
43
46
50
51
54
56
57
58
59
63
69
70
71
72
75
76
77
Safety Precautions ......................................................
Unpacking & Inspection ..............................................
Components Overview ................................................
Unit Mounting & Location ............................................
Unit Dimensions ..........................................................
Service Access / Airflow Clearances and
Unit Base Dimensions .................................................
Unit Lifting Procedures ................................................
Condensate & Safety Tray Drainage Instructions .......
Banking of Units...........................................................
Parts Layout ................................................................
Supply & Return Angle Plate Installation .....................
Supply & Return Angle Plate Assembly / Installation ....
Electrical Mains & Isolator Installation .........................
Compressor Shipping Blocks Removal .......................
Air Filter Installation .....................................................
Circuit Breaker Size & Cable Sizes .............................
Maximum Cable Lengths ............................................
Control Interface Remote Location ..............................
Data Cable & RJ12 Plug Preparations ........................
Dual Control Interface Connection Procedures ...........
BMS Control Installation Procedure ............................
2
2
3
3
4
8
9
10
11
13
17
18
19
20
21
22
23
24
25
27
28
Содержание PKY470T-6Q2
Страница 78: ...THIS PAGE WAS INTENTIONALLY LEFT BLANK ...
Страница 79: ...THIS PAGE WAS INTENTIONALLY LEFT BLANK ...
