manualshive.com logo in svg

ABB UMC100.3, Руководство пользователя

Поделиться
Скачать
ABB UMC100.3 Скачать руководство пользователя страница 91

Control Function Softstarter

Use this function to control a softstarter. The UMC acts as communication interface for the softstarter.

The following protection functions are not active during ramp-up and ramp-down:
•   Frequency out of range
•  Unbalance
•  Phaseloss
•  Internally calculated ground fault
During ramp-up and ramp-down and a connected voltage module the power and cos-phi values are invalid.
The control function softstarter must not be used for ATEX applications.

•  Check-back supervision must be set to "Current"
•  Relay output DO0 is used by the control function to activate the forward contactor
•  Relay output DO1 is used from the control function to activate the reverse contactor
•  Relay output DO2 provides the start/stop signal for the softstarter
•  DI0 is used as ramping information for the UMC in case a Softstarters provides this signal (see below)  

Set multifunction input DI0 to “Off”. It must not be configured for any other function in this case.

•  Optionally DI3 / DI4 can be used to start the motor and DI5 to stop the motor
•  Optionally DO3 can be used as a fault output 

For softstarters without by-pass signal

 it is necessary to configure a ramp-up time. After this time the UMC assumes the ramp-up 

to be finished and protection functions listed in the box above are activated again. To configure the ramp-up time use the YD-Star-
ting-Time parameter. A value < 3600 seconds must be set. After the start command the UMC immediately closes the main contac-
tor but awaits an additional delay (paramter Delay1) till the start command is signalled to the softstarter.
Stopping: After the stop signal the UMC immediately opens DO2 to signal the stop to the softstarter. The UMC detects the end of 
the ramp-down phase automatically by monitoring the motor current (I < below lower measurement range).  
Check back supervison must be set to "Motor current" for that reason. After ramp-down was detected an additional delay (para-
meter Delay2) is awaited until the forward or reverse contactor is opened.
Checkback delay time has to be configured equal or larger than the time configured for Delay 1 or Delay 2. Delay 1 and delay 2 are 
predefined but can be changed using the custom application editor.

Softstarters providing a ramping signal

 it is recommended to use this signal and connect it to digital input DI0 of the UMC. The 

Multifunction Input 0 must be set to Off in this case.
The parameter YD-Starting-Time must be set to 3600 seconds in this case. 

—

Monitoring Data for Softstarter

Word

Byte

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit1

Bit 0

0

0

Summary 
Warning

Summary 
Fault

Local Control Reverse 

Lockout 
Time

Overload 
warning

Run  
Forward

Off

Run  
Reverse

1

UMC100 DI5

UMC100 DI4

UMC100 DI3

UMC100 DI2

UMC100 DI1

UMC100 DI0

-

-

1

2, 3

Remaining data see section Parameters and Data Structures on a Fieldbus

2

4, 5

3

6, 7

4

8, 9

5

10.11

6

12

13

7

14

15

The table above represents the data allocation as realised with the built-in standard applications. It may differ for 
customer-specific applications!

91

CO N FI G U R I N G  T H E  M OTO R  M A N AG EM EN T  FU N C T I O N S

Содержание UMC100.3

































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды