manualshive.com logo in svg

ABB i-bus KNX JRA/S 6.230.3.1, Руководство по эксплуатации продукта

Поделиться
Скачать
ABB i-bus KNX JRA/S 6.230.3.1 Скачать руководство пользователя страница 92

ABB i-bus

®

 KNX 

Commissioning 
 
 

90   2CDC506083D0201 | JRA/S 6.230.3.1 

In the following table, the Forced operation function is explained: 

Bit 1 

Bit 0 

Access 

Description 

0 

0 

Enabled  The Switch group object of the actuator is enabled by the binary input. The assigned 

sensor can control the actuator via the Switch object. The binary input does not control the 
actuator. Bit 0 of the value of the Forced operation group object is not evaluated. The 
Forced operation group object sends a telegram with the group addresses of the Forced 
operation group object and the status of the Switch group object every time the latter 
changes status. 

0 

1 

Enabled 

1 

0 

Off 

The Switch group object of the actuator is disabled by the binary input. The assigned 
sensor cannot control the actuator via the Switch group object. The binary input controls 
the actuator via the Forced operation group object. The actuator is switched off. Bit 0 of the 
value of the Forced operation group object is evaluated. 

1 

1 

On 

The Switch group object of the actuator is disabled by the binary input. The assigned 
sensor cannot control the actuator via the Switch group object. The binary input controls 
the actuator via the Forced operation group object. The actuator is switched on. 

 

8-bit scene 

Options: 

1…64 

This parameter defines the scene number, which is sent on actuation. 

Recall/store scene 

Options: 

Recall 
Save 

This parameter defines whether the scene is to be recalled or stored. 

Hour [0...23] 

Options: 

0…23 

Minute [0...59] 

Options: 

0…59 

Seconds [0…59] 

Options: 

0…59 

These parameters set the hours, minutes and seconds to be sent on operation.  

Содержание i-bus KNX JRA/S 6.230.3.1

























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды