manualshive.com logo in svg

ABB i-bus KNX JRA/S 6.230.3.1, Руководство по эксплуатации продукта

Поделиться
Скачать
ABB i-bus KNX JRA/S 6.230.3.1 Скачать руководство пользователя страница 134

ABB i-bus

®

 KNX 

Planning and application 
 
 

132   2CDC506083D0201 | JRA/S 6.230.3.1 

The Logic function is always re-calculated when a group object value is received.  

Gate function example 

•

 

The GATE connection is set to disable as soon as the communication object 

Logical connection x 

receives a 0. 

•

 

The output of the logical connection is 0. 

•

 

The communication object 

Logical connection 1

 receives a 0, i.e. the GATE is disabled. 

•

 

The communication object 

Switch

 receives 0, 1, 0, 1. The output of the logic operation always 

remains 0. 

•

 

The 

Logical connection x

 group object receives a 1, i.e. the GATE is enabled if it is set in the 

parameters. 

•

 

The output of the logical connection is recalculated. 

 

Note 

The values of group objects 

Logical connection 1/2

 are stored on bus voltage failure. The values are set 

again after bus voltage recovery 
If values are not assigned for these group objects 

Logical Connection 1/2

 they will be deactivated. 

On reset via the bus, the values of group objects 

Logical Connection 1/2

 remain unchanged. 

 

Note 

If telegrams are received on the 

Switch

 group object during the block, they will not be stored. 

For this reason, the output or the event remain unchanged when the GATE is enabled. 
The output switches if the GATE is enabled and a telegram is received on the 

Switch

 group object. 

Содержание i-bus KNX JRA/S 6.230.3.1

























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды