manualshive.com logo in svg

ABB i-bus KNX JRA/S 6.230.3.1, Руководство по эксплуатации продукта

Поделиться
Скачать
ABB i-bus KNX JRA/S 6.230.3.1 Скачать руководство пользователя страница 21

ABB i-bus

®

 KNX 

Commissioning 
 
 

JRA/S 6.230.3.1 | 2CDC506083D0201   19 

Sending and switching delay after bus 
voltage recovery in s [2…255] 

Options: 

2…255 

During the sending and switching delay, telegrams are only received. However, the telegrams are not 
processed and the outputs remain unchanged. No telegrams are sent on the bus. 

After the sending and switching delay, telegrams are sent and the state of the outputs is set to correspond 
with the parameterization or the communication object values. 

If group objects are read out via the bus during the sending and switching delay, e.g. by a visual display 
system, these requests are stored and a response is sent once the delay time has expired. 

An initialization time of about two seconds is included in the delay time. The initialization time is the time 
that the processor requires before it is ready to function. 

How does the device react on bus voltage recovery? 

After bus voltage recovery, the device always waits for the sending delay time to elapse before 
sending telegrams via the bus. 

Rate of telegrams 

Options: 

Not limited 
Send maximum 1 telegram/s 
Send telegram every 0.1 s 

•

 

Send maximum 1 telegram/s

: No more than one telegram is sent per second.  

•

 

Send telegram every 0.1 s

: A telegram is sent every 0.1 seconds. 

This parameter limits the bus load of the device depending on its parameterization. 

Содержание i-bus KNX JRA/S 6.230.3.1

























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды