ABB i-bus KNX JRA/S 6.230.3.1 Скачать руководство пользователя страница 22

Страница: 22 / 152

ABB i-bus

KNX

Commissioning

20 2CDC506083D0201 | JRA/S 6.230.3.1

Send group object
"In operation"

Options:

No
Send value 0 cyclically
Send value 1 cyclically

The communication object

In operation

indicates the presence of the device on the bus. This cyclic

telegram can be monitored by an external device. If a telegram is not received, the device may be
defective or the bus cable to the transmitting device may be interrupted.

•

: The communication object

In operation

is not enabled.

•

Send value 0/1 cyclically

: The

In operation

group object (no. 0) is sent cyclically via KNX.

The following parameter appears:

Sending cycle time
in s [1...65,535]

Options:

1…60…65,535

The time interval, at which the communication object

In operation

(No. 0) cyclically sends a

telegram, is set here.

Note

After bus voltage recovery the group object sends its value after the set sending and switching
delay.

Enable group object
"Request status values" 1 bit

Options:

No
Yes

•

Yes

: The 1-bit communication object

Request status values

is enabled.

Via this communication object, all status messages can be requested, provided that they have been
parameterized with the option

After a change or request.

With the option

Yes

, the following parameters appear:

Request with object value

Options:

0
1
0 or 1

•

: Sending status messages is requested with the value 0.

•

: Sending status messages is requested with the value 1.

•

0 or 1:

Sending status messages is requested with the values 0 or 1.

Содержание i-bus KNX JRA/S 6.230.3.1

























































































































































Результаты поиска

Содержание i-bus KNX JRA/S 6.230.3.1

Отзывы:

Бренды по названию

Популярные бренды

ABB i-bus KNX JRA/S 6.230.3.1, Руководство по эксплуатации продукта

Результаты поиска

Содержание i-bus KNX JRA/S 6.230.3.1

Отзывы:

Бренды по названию

Популярные бренды