manualshive.com logo in svg

ABB i-bus KNX JRA/S 6.230.3.1, Руководство по эксплуатации продукта

Поделиться
Скачать
ABB i-bus KNX JRA/S 6.230.3.1 Скачать руководство пользователя страница 114

ABB i-bus

®

 KNX 

Commissioning 
 
 

112   2CDC506083D0201 | JRA/S 6.230.3.1 

No. 

Function 

Object name 

Data type 

Flags 

82 

Sun 

Blind Output A,B  

Shutter Output A,B  

1 bit 

DPT 1.001 

C, W 

This group object is enabled if the 

Enable function Automatic

 parameter is set to 

Yes

 in the 

A, B: Blind

 parameter window. 

This group object activates sun protection: The blind moves to the sun screening position. 

Incoming telegrams on this group object are only considered if the group object 

Activation of autom. control

 has the value 1. 

If the 

Sun

 group object receives a telegram with the value 1, the blind moves to the parametrized position for Sun = 1. If the 

object receives a telegram with the value 0, the blind moves to the parametrized position for sun = 0. 

The execution of a reaction to incoming telegrams can be delayed via the parameter Delay for sun = 1 and Delay for sun = 0, 
in order to prevent the shutters/blinds continuously moving up and down in changeable weather. If a telegram with the 
opposing value is received within the delay time, Position for sun = 1 is not executed and the blind remains in the Position for 
sun = 0 position or vice versa. 

If Position for sun = 1 is set to 

Receive position via 8-bit values

, then once the delay has elapsed, the output moves to the last 

position received on the group objects 

Move to pos. for sun [0..255]

 (blinds and shutters) and 

Adjust slat for sun [0…255]

 

(blinds only). 

Telegram value: 

0 = no sun 
1 = sun 

 

83 

Move to pos. for sun 

Blind Output A,B  

Shutter Output A,B  

1 byte 

DPT 5.001 

C, W 

This group object is enabled if the 

Enable function Automatic

 parameter is set to 

Yes

 in the 

A, B: Blind

 parameter window. 

This group object sets the position during active sun protection. 

Incoming telegrams on this group object are only executed immediately if automatic control is activated (Activation of autom. 
control = 1) and the sun is shining (sun = 1). The blind is then positioned according to the received value. 

Telegram value: 

0  

= upper 

…  

= Intermediate position 

255   = lower 

 

84 

Sun slat adjust.  

Blind Output A,B  

 

1 byte 

DPT 5.001 

C, W 

This group object is enabled if the 

Enable function Automatic

 parameter is set to 

Yes

 in the 

A, B: Blind

 parameter window. 

This group object sets the slat position during active sun protection and is thus only available with blind operation. 

Incoming telegrams on this group object are only executed immediately if automatic control is activated (Activation of autom. 
control = 1) and the sun is shining (sun = 1). The slats are then positioned according to the received value. 

The Move telegram 

Move to pos. for sun [0..255]

 is always moved to the target position before the positioning of the slats is 

executed. 

Telegram value: 

0 

 = slats fully OPEN 

…  

= Intermediate position 

255  = slats CLOSED  

 

Содержание i-bus KNX JRA/S 6.230.3.1

























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды