manualshive.com logo in svg

ABB i-bus KNX JRA/S 6.230.3.1, Руководство по эксплуатации продукта

Поделиться
Скачать
ABB i-bus KNX JRA/S 6.230.3.1 Скачать руководство пользователя страница 41

ABB i-bus

®

 KNX 

Commissioning 
 
 

JRA/S 6.230.3.1 | 2CDC506083D0201   39 

Object value "Switch" on 
bus voltage recovery 

Options: 

Do not write 
Write with "0" 
Write with "1" 

This parameter allows the output to be influenced by the value of the 

Switch

 group object on bus voltage 

recovery. 

The 

Switch

 group object can be written with either 0 or 1 when the bus voltage recovers. The contact 

position is redefined and set based on the set device parametrization. 

•

 

Do not write

: The group object assumes the value 0. This value remains in place until changed by 

the bus and is not recalculated until this point. 

Note 

Take note of the reaction on bus voltage failure, recovery and download. 
The blind/shutter actuator draws the energy for switching the contact from the bus. After bus voltage 
is applied, it takes about ten seconds before sufficient energy is available to switch all contacts 
simultaneously. 
Depending on the sending and switching delay on bus voltage recovery set in the 

General

 parameter 

window, the individual outputs will only assume the required contact position after this time. 
If a shorter time is set, the JRA/S will only switch the first contact when sufficient energy is stored in the 
blind/shutter actuator, in order to ensure that enough energy is available to immediately switch all 
outputs safely to the required contact position if there is another bus voltage failure. 

 

Enable function Time 

Options: 

No 
Yes 

•

 

No

: The parameter window remains disabled and invisible. 

•

 

Yes

: The 

- Time

 parameter window appears. 

Enabling the 

Time

 function enables the 

- Time

 parameter window. Further settings can be made here, 

e.g. on and off delays or staircase lighting.  

Note 

For a more precise description of the function, see Output A group objects , p. 106 

 

Содержание i-bus KNX JRA/S 6.230.3.1

























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды