manualshive.com logo in svg

ABB i-bus KNX JRA/S 6.230.3.1, Руководство по эксплуатации продукта

Поделиться
Скачать
ABB i-bus KNX JRA/S 6.230.3.1 Скачать руководство пользователя страница 108

ABB i-bus

®

 KNX 

Commissioning 
 
 

106   2CDC506083D0201 | JRA/S 6.230.3.1 

3.4.4.2 

Output A group objects  

No. 

Function 

Object name 

Data type 

Flags 

75 

Switch 

Output A 

1 bit  

DPT 1.001 

C, W 

This group object is enabled if the 

Mode Output

 parameter is set to 

Switch actuator

 in the 

Output A, B: Mode

 parameter 

window. 

This group object switches the output ON/OFF. The device receives a Switch telegram via the Switch group object. 

N/O: 

Telegram value  

1 = switch ON 
0 = Switch OFF 

N/C: 

Telegram value  

1 = switch OFF 
0 = Switch ON 

 

Note 

With logical connections or forced operations, a change in the 

Switch

 group object does not necessarily result in a 

changed contact position.  

For further information see: Function diagram, p. 126 
 

 

 

76 

Permanent on 

Output A 

1 bit 

DPT 1.003 

C, W 

This group object is enabled if the 

Enable function Time

 parameter is set to 

Yes 

in the 

Output A,B: Switch actuator

 parameter 

window. 

If the communication object is assigned with the value 1, the output is switched on irrespective of the value of the 
communication object 

Switch

 and remains switched on until the communication object 

Permanent ON

 has the value 0. When 

the Permanent ON state ends, the state of the communication object 

Switch

 is used. 

Permanent ON only switches ON and "masks" the other functions. This means that the other functions, e.g. Staircase lighting, 
continue to run in the background but do not initiate a switching action. When permanent ON ends, the contact position which 
would result without the permanent ON function becomes active. For the 

Staircase lighting

 function the reaction after 

Permanent ON is parametrized in 

Output

 

A,B: Switch actuator - Time

 parameter window, p. 42. 

This communication object can be used, for example, to allow service or maintenance and cleaning personnel to initiate a 
permanent ON. The device receives a switch telegram via the switch object. 

Permanent ON becomes inactive after a download or bus voltage recovery. 

Telegram value 

1 = activates permanent ON mode 
0 = Deactivates permanent ON mode 

 

Содержание i-bus KNX JRA/S 6.230.3.1

























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды