manualshive.com logo in svg

ABB i-bus KNX JRA/S 6.230.3.1, Руководство по эксплуатации продукта

Поделиться
Скачать
ABB i-bus KNX JRA/S 6.230.3.1 Скачать руководство пользователя страница 84

ABB i-bus

®

 KNX 

Commissioning 
 
 

82   2CDC506083D0201 | JRA/S 6.230.3.1 

How does 1 button dimming function? 

Switch and dim functions can be controlled completely using a single push button. With each long 
operation alternate BRIGHTER or DARKER dimming occurs, or with short operation alternate 
switch on or off occurs. 

If the 

Switch

 group object = 0, a BRIGHTER telegram is sent at all times. In order to evaluate the 

switch feedback of the actuator, the Write flag of the 

Switch

 group object is set. 

The following table shows the function in detail: 

Switch group object value 

Value of the last dimming telegram 

Reaction of the dimming actuation 
(sends dimming telegram) 

OFF 

DARKER 

BRIGHTER 

OFF 

BRIGHTER 

BRIGHTER 

ON 

DARKER 

BRIGHTER 

ON 

BRIGHTER 

DARKER 

 

The advantage of the 

Only dimming

 function is that no distinction is made between short and long 

operation. Thus, the Dim telegram is initiated immediately after operation. It is not necessary to wait 
for a long operation. 

How does 2 button dimming function? 

If 2 button dimming is required, the functions of the individual buttons should be set with the 
parameters 

Reaction on short operation

 or 

Reaction on long operation

, e.g. ON or BRIGHTER. 

The user thus has the choice of the buttons to be combined with one another, e.g. to dim a lighting 
group or the function that the individual buttons should perform in this case. 

Furthermore, two inputs are required for 2 button dimming, e.g. 

Input a

 with short operation for ON 

and long operation for BRIGHTER. 

Input b

 with short operation for OFF and long operation for 

DARKER. 

Selecting the 

Dimming and switching

 option in the 

Function Dimming

 parameter unhides the parameters 

Long operation after…

, 

On short operation: Switch

 and 

On long operation: Dimming direction

 in the 

a: 

Dimming sensor

 parameter window: 

Long operation after… 

Options: 

0.3/0.4/0.5/0.6/0.8/1/1.2/1.5/2/3/4/5/6/7/8/9/10 s 

This defines the time period T

L

 after which an operation is considered a "long" operation. 

Содержание i-bus KNX JRA/S 6.230.3.1

























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды