ABB i-bus KNX JRA/S 6.230.3.1 Скачать руководство пользователя страница 87

Страница: 87 / 152

ABB i-bus

KNX

Commissioning

JRA/S 6.230.3.1 | 2CDC506083D0201 85

3.3.3.4

Input a: Value/forced operation parameter window

This operation mode allows values of any data type to be sent.

This parameter window is visible if the

Function

parameter is set to

Value/forced operation

Enable communication object
"Block" 1-bit

Options:

No
Yes

•

Yes:

The 1-bit group object

Block

is enabled. This can be used to disable the input.

Note

If the input is disabled and the option

Send cyclically

is set, the last state is still sent regardless of the

block. The option

Block

still blocks the physical input, sending continues internally.

Debounce time

Options:

10/20/30/50/70/100/150 ms

Debouncing prevents unwanted multiple operations of the input, e.g. due to bouncing of the contact.

For further information, see: What is the debounce time?

Содержание i-bus KNX JRA/S 6.230.3.1

























































































































































Результаты поиска

Содержание i-bus KNX JRA/S 6.230.3.1

Отзывы:

Бренды по названию

Популярные бренды

ABB i-bus KNX JRA/S 6.230.3.1, Руководство по эксплуатации продукта

Результаты поиска

Содержание i-bus KNX JRA/S 6.230.3.1

Отзывы:

Бренды по названию

Популярные бренды