ABB i-bus KNX JRA/S 6.230.3.1 Скачать руководство пользователя страница 102

Страница: 102 / 152

ABB i-bus

KNX

Commissioning

100 2CDC506083D0201 | JRA/S 6.230.3.1

3.4.3.1

group objects Switch sensor

No.

Function

Object name

Data type

Flags

Block

Input a: Switch sensor

1 bit

DPT 1.003

C, W

This group object is enabled if the

Enable group object "Block" 1 bit

parameter is set to

Yes

in the

Input

a: Switch sensor

parameter window.

Using the communication object

Block

, the input can be blocked or enabled. With activated communication object

Block

the

inputs are blocked.

Note

When the input is blocked there is fundamentally no reaction to a signal change on the input, but:

– Waiting for a long button operation or a minimum signal duration is suspended.

– Parametrized

Cyclic sending

is not interrupted.

– It is still possible to write the

Switch x

group object.

If the input state changed during the blocked phase, this leads to immediate sending of the new communication
object value after enabling. If the input state remains the same during the blocking phase, the communication object
value is not sent.

Telegram value:

0 = enable input a
1 = Block input a

Switch 1

Input a: Switch sensor

1 bit

DPT 1.001

C, W, T

This group object is enabled if the

Function

parameter is set to

Switch sensor

in the

Input a

Function

parameter window and

the “

Switch 1

” parameter is set to

Yes

in the

Input a

Objects “Switch”

parameter window.

In accordance with the parameter setting, this group object can be switched by actuating the input to

ON, OFF

TOGGLE

can be set to

No reaction

. With toggle the previous value, e.g. 1, is toggled directly to the value 0. The group object can be

sent cyclically, e.g. for sensor lifesign monitoring.

Note

The communication object can be written to externally. Thus cyclic sending is interrupted or may not be possible
depending on the parameter setting.

No further group objects are visible with the setting.

Telegram value:

0 = OFF
1 = ON

Switch 2

Switch 3

See communication object 46.

Start event 0/1

Input a: Switch sensor

1 bit

DPT 1.001

C, W

This group object is enabled if the

"Start event 0/1" 1 bit

parameter is set to

Yes

in the

Input a: Switch sensor

parameter

window.

The 1-bit communication object

Start event 0/1

is enabled. As a result, the same events, except those of the push

button/switch connected to the binary input, can also be triggered by the receipt of a telegram on the communication object

Start event 0/1

Telegram value:

0 = start event 0
1 = Start event 1

Содержание i-bus KNX JRA/S 6.230.3.1

























































































































































Результаты поиска

Содержание i-bus KNX JRA/S 6.230.3.1

Отзывы:

Бренды по названию

Популярные бренды

ABB i-bus KNX JRA/S 6.230.3.1, Руководство по эксплуатации продукта

Результаты поиска

Содержание i-bus KNX JRA/S 6.230.3.1

Отзывы:

Бренды по названию

Популярные бренды