ABB i-bus KNX JRA/S 6.230.3.1 Скачать руководство пользователя страница 104

Страница: 104 / 152

ABB i-bus

KNX

Commissioning

102 2CDC506083D0201 | JRA/S 6.230.3.1

3.4.3.3

Blind sensor group objects

No.

Function

Object name

Data type

Flags

Block

Input a:

Blind sensor

1 bit

DPT 1.003

C, W

This group object is enabled if the

Enable group object "Block" 1 bit

parameter is set to

Yes

in the

Input a: Blind sensor

parameter window.

Using the communication object

Block

, the input can be blocked or enabled. With activated communication object

Block

the

inputs are blocked.

Note

When the input is blocked there is fundamentally no reaction to a signal change, but:

– Waiting for a long button operation or a minimum signal duration is suspended.

– Parametrized

Cyclic sending

is interrupted.

– Group objects continue to be updated and sent if necessary.

When enabling an input, a change of the signal states (as opposed to before the block) leads to immediate
processing, e.g.:

– The minimum actuation or detection of a long/short button push starts.

– Group objects send their current value if necessary.

Telegram value:

0 = enable input a
1 = Block input a

Blind UP/DOWN

Input a:

Blind sensor

1 bit

DPT 1.008

C, W, T

This group object is enabled if the

Function

parameter is set to

Blind sensor

in the

Input a

Function

parameter window.

This group object sends a blind UP or DOWN Move telegram on the bus. By receiving telegrams, the device also recognizes
Move telegrams from another sensor, e.g. parallel operation.

Telegram value

0 = UP
1 = DOWN

STOP/slat adjustment

Input a:

Blind sensor

1 bit

DPT 1.007

C, T

This group object is enabled if the

Function

parameter is set to

Blind sensor

in the

Input a

Function

parameter window.

This communication object sends a STOP telegram or slat adjustment.

Telegram value

0 = STOP/slat adjustment UP
1 = STOP/slat adjustment DOWN

Содержание i-bus KNX JRA/S 6.230.3.1

























































































































































Результаты поиска

Содержание i-bus KNX JRA/S 6.230.3.1

Отзывы:

Бренды по названию

Популярные бренды

ABB i-bus KNX JRA/S 6.230.3.1, Руководство по эксплуатации продукта

Результаты поиска

Содержание i-bus KNX JRA/S 6.230.3.1

Отзывы:

Бренды по названию

Популярные бренды