Zurich 56218 Owner'S Manual Download Page 11

Page: 11 / 101

Using the Scan Tool

CODE RETRIEVAL PROCEDURE

For technical questions, please call 1-888-866-5797.

If a recommended solution for the “priority” DTC is not available, an
advisory message displays. Press

DTC/FF

to scroll to the next DTC.

In the case of long code definitions, a small arrow is shown in the
upper/lower right-hand corner of the display area to indicate the
presence of additional information.
If a definition for the currently displayed code is not available,

an advisory message shows.

12.

Read and interpret Diagnostic Trouble Codes/system condition using

the display and the green, yellow and red LEDs.

The green, yellow and red LEDs are used (with the display) as

visual aids to make it easier to determine engine system

conditions.

Green LED

– Indicates that all engine

systems are “OK” and operating

normally. All monitors supported by

the vehicle have run and performed

their diagnostic testing, and no trouble

codes are present. All Monitor icons

will be solid.

Yellow LED

– Indicates one of the

following conditions:

. A PENDING CODE IS PRESENT – If

the yellow LED is illuminated, it may

indicate a Pending code is present.

Check the display for confirmation. A

Pending code is confirmed by the

presence of a numeric code and the

word PENDING.

. MONITOR NOT RUN STATUS – If

the display shows a zero (indicating

there are no DTC’s present in the

vehicle’s computer memory), but the

yellow LED is illuminated, it may be an

indication that some of the Monitors

supported by the vehicle have not yet

run and completed their diagnostic

testing. Check the display for

confirmation. All Monitor icons that are

blinking

have not yet run and

completed their diagnostic testing; all

Monitor icons that are

solid

have run

and completed their diagnostic testing.

Red LED

– Indicates there is a

problem with one or more of the

vehicle’s systems. The red LED is

also used to indicate that DTC(s) are

present. In this case, the Malfunction

Indicator (Check Engine) lamp on

the vehicle’s instrument panel will be

illuminated.

Summary of Contents for 56218






































































































Search results

Summary of Contents for 56218

Reviews:

Related manuals for 56218

Brands by name

Popular brands

Zurich 56218, Owner'S Manual

Search results

Summary of Contents for 56218

Reviews:

Related manuals for 56218

Brands by name

Popular brands