Zurich 56218 Owner'S Manual Download Page 4

Page: 4 / 101

Scan Tool Controls

CONTROLS AND INDICATORS

For technical questions, please call 1-888-866-5797.

CONTROLS AND INDICATORS

Figure 1. Controls and Indicators

See Figure 1 for the locations of items 1 through 16, below.

ERASE button

- Erases Diagnostic Trouble Codes (DTCs), and

“Freeze Frame” data from the vehicle’s computer, and resets Monitor
status.

SYSTEM MENU

button – When pressed, displays the System

Menu.

DTC/FF button

- Displays the DTC View screen and/or scrolls the

LCD display to view DTCs and Freeze Frame data.

POWER/LINK button

- When not connected to a vehicle,

turns the Scan Tool “

” and “

Off

” (press and hold for 3 seconds).

When connected to a vehicle, links the Scan Tool to the vehicle’s
PCM.

M button

– When pressed, displays the Main Menu.

LD button

– When pressed while linked to a vehicle, places the Scan

Tool in Live Data mode.

UP button

– When in MENU mode, scrolls UP through the menu

options. When LINKED to a vehicle, scrolls UP through the current
display screen to display additional data.

ENTER button

- When in MENU mode, confirms the selected

option or value.

Summary of Contents for 56218






































































































Search results

Summary of Contents for 56218

Reviews:

Related manuals for 56218

Brands by name

Popular brands

Zurich 56218, Owner'S Manual

Search results

Summary of Contents for 56218

Reviews:

Related manuals for 56218

Brands by name

Popular brands